Table of Contents
Without it the bondo won’t get hard. Put a small piece of bondo on a board and run a line of hardener from end to end. It will take about five minutes to mix it up and apply it. If it starts tacking up, stop applying it or you’ll mess it up.
Does Bondo filler need hardener?
How Much Hardener Do You Add To Your Body Filler? You need to be sure to add the right amount of hardener to your Bondo; adding more than enough will cause your body filler to dry faster and give you less time for shaping and laying your filler on your panels.
Do I need hardener with Bondo?
(Bondo comes with a tube of hardener.) If you add too much hardener, the mixture will gel too quickly. If you add too little, it increases the amount of time for it to cure, and if you don’t add enough it will never cure.
What to do if you didn’t add enough hardener to resin?
How do I Cure Fiberglass Resin That Doen’t Have Enough Hardener Set the fiberglass in the sun. The curing of fiberglass resin is an exothermic reaction, meaning that heat makes it work. Use a heat gun on the fiberglass. Spray a mist of catalyst onto the fiberglass with a spray bottle.
Can you use Bondo wood filler without hardener?
Wood fillers can be used to reinforce softwoods or rotten woods structurally. However, this is usually only a stopgap without using a hardener as well. You can use both in conjunction to save ancient, fragile woods. For normal use, the wood filler should suffice.
How long does Bondo take to harden?
Allow the putty to dry 15 minutes at 77 degrees F (25 degrees C). In cooler climates, putty may take 20-30 minutes to dry. 7. Using 3M™ Sandpaper 80 grit, sand and shape the filled area to the contour of the surface.
What happens if you don’t put enough hardener in body filler?
Adding too much hardener will result in rapid gelling of the mixture, making it hard to get coverage in time. Too little hardener will increase cure time, but there’s a point where the filler won’t ever harden and you won’t know it until you try to sand.
Why is my Bondo still tacky?
It could just be the skim on the top that stays sticky. Some lower quality fillers don’t have the additives required to stop that from happening. Try sanding it, if it remains soft and clogs your paper after that first top coat has been removed then you need to take all off.
Why is Bondo bad?
Unfortunately, filling compounds such as Bondo also present some drawbacks. Fillers like Bondo can crack if they are mixed too thickly, harming rather than improving the look of the car. Additionally, there’s a risk of discoloration and poor long-term wear when you use a dent repair filler like Bondo.
What happens if you use Bondo without hardener?
Without it the bondo won’t get hard. Put a small piece of bondo on a board and run a line of hardener from end to end. It will take about five minutes to mix it up and apply it. If it starts tacking up, stop applying it or you’ll mess it up.
Why is my resin not hardening?
If your epoxy resin hasn’t cured properly, this means that the chemical reaction between the resin and hardener was not able to take place. Sticky resin is typically caused by inaccurate measuring or under mixing. Try moving your piece to a warmer spot: if it doesn’t dry, re-pour with a fresh coat of resin.
How do you harden uncured epoxy?
Tips and Tricks to harden sticky resin Make sure the ambient temperature of your workspace is 75-85°F (24-30°C) Make sure you add maximum 6%, by volume, colorant to your epoxy mixture. Make sure you follow the correct mixing ratio for resin and hardener. Make sure you mix thoroughly for at least 3 minutes.
How do you harden bendy resin?
Resin poured in a thin layer Some resins, especially doming resins, can be flexible after the full cure time. It may firm up by giving it more curing time, but that doesn’t always work. If you want to give the resin extra time to cure, make sure it stays warm and give it another two to seven days to fully cure.
Does Minwax wood filler harden without hardener?
No, the heat will just soften it. It takes the catalyst mixed through it to make it harden.
How do you harden wood filler?
Apply the wood filler to the hole with the putty knife, and press the filler in tightly to the area. Apply the layers in thin coats to make it dry faster. The thicker you make the layers, the more water there is to be absorbed, which will lengthen drying times.
How long can you leave Bondo unpainted?
Between life and work, the longest time period the bondo would go Unpainted would be about 2-3 weeks.
Can you paint over body filler?
Fillers and putties will normally work OK over properly sanded (80-180 grit) cured OEM paint. However, with so many different types of aftermarket paint available (lacquer, enamel, urethane, water-based). We recommend that all paint be removed where filler is to be applied.”Nov 3, 2012.
Why does my Bondo dry so fast?
It’s hotter out, so the inital hardening is going to kick in faster. As was mentioned above, the bondo gets hot anyway, but you’re starting out at a hotter temp to begin with during the summer, so the hardening kicks in quicker.
How much hardener do you put in Bondo?
2. Place the proper amount of Bondo filler and hardener: 50:1.
How long does it take Bondo body filler to dry?
Properly mixed, body filler will begin to thicken in 10-15 minutes, and be fully cured in 30.
Can you sand tacky Bondo?
You can go ahead and sand it. If it clogs your paper after you cut through the outside sticky “Film”,,go ahead and strip it off and start over. You didnt put enough hardener in it.
What temperature does Bondo cure at?
Bondo says 45-50 degrees.
Does acetone remove Bondo?
Acetone will remove at least some fabric along with the embedded Bondo. Apply the acetone to a cleaning cloth and wipe the affected area thoroughly. According to the Aftermarket Product Department of 3M, the Bondo should release from the fabric fairly easily.
