Table of Contents
Why does my water heater not stay lit?
Your thermocouple senses when your pilot light is burning. If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
When I release the pilot button the flame goes out?
If you’re able to light the pilot light, but it goes out when you release the control knob, the thermocouple probably needs replacing. The thermocouple is a safety device that shuts off gas flow if it senses the pilot light is out, but when damaged it loses its regulatory ability.
What do you do when your water heater keeps turning off?
What To Do If Your Gas Water Heater Keeps Shutting Off Call Your Plumber. The first thing you should do is call your plumber. Gas Supply Problems. Your gas water heater will turn off if it isn’t getting the fuel it needs. Dirty Thermopile or Pilot Light. Dirty Air Inlet.
How do you clean a thermocouple on a water heater?
Clean the thermocouple – using the emery cloth sandpaper, sand the ends of the thermocouple and then give it a finishing touch with the lint-free cloth. Hopefully, you can get to the ends of the thermocouple without having to detach it from the assembly, but you may have to do that.
How do I know if my thermocouple is bad on my water heater?
If the pilot lights but the flame goes out as soon as you release the button after holding it for 60 seconds, then the thermocouple is bad. It’s possible to replace the thermocouple without removing the burner assembly, and many repair people do this.
What would cause a pilot light to not stay lit?
The Buildup of Dirt or Debris Around The Pilot Light – Over the years it’s easy for dust, debris, and dirt to build up on the inside of the intake valve where the pilot light resides. This makes it difficult for the flame to breath and as a result causes the pilot light to go out suddenly.
What would cause a pilot light to keep going out?
A faulty, misaligned, dirty, or damaged thermocouple is often the culprit behind your pilot light going out. The thermocouple is an automatic safety shutoff device that prevents the gas valve from opening if the pilot light is out.
Why won’t the pilot stay lit on my wall heater?
The Pilot Won’t Stay Lit A pilot that won’t stay lit could be the result of a blockage in the pilot tube. Turn off the gas, clear the tube with compressed air, and relight the pilot. If that doesn’t work, you may need to call a repairman to come and install a new thermocouple.
How much does it cost to replace a thermocouple?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
How long does a water heater thermocouple last?
Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
How do I know if my thermocouple is working?
Test the Thermocouple If the thermocouple is working, you should be able to measure 30 to 40 millivolts of voltage at the connection end of the tube when the pilot flame is on. You can test this yourself using a multimeter, but you may need a helper to keep the pilot flame burning while you do it.
Can you bypass a water heater thermocouple?
Realistically, you have just disabled the thermocouple, but you can also reach in and unclip it from its holding bracket where it meets the pilot light. In most cases it will be held on with a gravity clip, but some are held on with a screw that must be removed with a small screwdriver.
Where is a thermocouple located?
Your furnace’s thermocouple is usually located right in the flame of the furnace’s pilot light. Its copper tubing makes it easy to spot. The thermocouple is made up of a tube, a bracket, and wires.
Can you replace a thermocouple yourself?
1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.
What happens if thermocouple is bad?
Normally when the thermocouple malfunctions or isn’t working, it simply shuts off the gas to your heater. This is important, particularly if the pilot light is out, because it prevents harmful gas from leaking into your home.
