Table of Contents
First, check your water level. Then, look for clogs in your circulation system, and wash or change your filter. If the high limit switch shut your heater off because your water got too hot or you have air trapped in your lines, resetting the heater will get it going again.
Why won’t the jets on my hot tub turn off?
When jets start failing, the most likely case is that your hot tub pump is not working correctly. Open the access panel and the airlock valve close to the pump. This releases air from the line and purge system, allowing more water to stream through the jets. Clogged filters or water intakes can also cause jet issues.
Why do my hot tub jets keep turning on?
That said, the jets will turn on automatically if the internal temperature falls below what you set it to. For example if it is set to 104, but the internal temp falls to 103, the jets will turn on automatically, until it heats back up to 104 and then turn off automatically.
How do you turn off hot tub jets?
To toggle the pumps on and off, simply press the jets you would like turned off. That will switch off the therapy pump you indicated. Note: The circulation pump cannot be toggled on and off on the touch screen as it is designed to run at all times to keep the hot tub running effectively.
Should hot tub jets always be on?
A dip in the spa can be a spontaneous event whenever the mood strikes. Since your hot tub pump circulates the warm water as well as the sanitizer, a general rule is to follow manufacturer recommendations or leave the pump on for a minimum of eight hours per day.
Do spa jets turn off automatically?
Why do the jets turn off by themselves? The water jets on almost all systems (Balboa, Gecko, Smart Touch, etc.) will only run for a fixed time, usually 15 or 20 minutes, and then will automatically switch off.
Where is the reset button on a hot tub?
Locate the spa’s high-limit reset. This is a red button found on many spa packs. It may be located on the heater and covered by a rubber nipple.
Can you leave a hot tub turned off?
The answer is yes! Hot tubs are designed to be left on permanently and this is how they work best. Of course, they’ll need to be drained regularly but for the most part, they are left on 24/7.
What temperature should a hot tub be when not in use?
While it may sound like common sense to turn your hot tub down every time it is not in use, it’s actually better to maintain a constant soaking temperature, which is typically around 100° Fahrenheit for many people.
Do hot tub jets run when heating?
Before covering your hot tub, make sure to turn on the jets as this will accelerate the pace of your hot tub’s heating. By running the jets, you’re allowing the heated water to be circulated and evenly distributed to all areas of the hot tub.
Can I leave hot tub jets on with cover on?
Covering your hot tub with plastic wrap or a tarp is disastrous for your hot tub cover. Not only could it become waterlogged much quicker, but it can also magnify the sun’s rays and trap heat. That can cause your cover’s cores to melt.
How long should a hot tub run each day?
Continuously? Most residential spa owners do not need to run their hot tub pumps all the time. Unless the spa is used multiple times per day, a filtration cycle of 2-8 hours, twice a day, should be enough to keep most hot tubs sanitary.
Can you run hot tub jets with cover on?
You can open the spa cover and run the jets and this will help a little, but depending on how over-chlorinated it is, it might take a while until it’s safe to use the hot tub.
Is a hot tub always on?
Hot tubs are designed to always be switched on and it’s more economical to keep the water hot than it is to heat it up from cold each time you want to use it.
Can you run hot tub jets without water?
Water left in the pipes and equipment can grow bacteria biofilm, which is difficult to eradicate. Plus, without water, seals and gaskets become dry and begin to leak. Therefore, make sure to not leave your hot tub sitting empty.
Where is the power switch on a hot tub?
The pressure switch is often located either on a PVC plumbing part next to the spa pack or directly mounted onto the stainless steel heater manifold or tube. The heater manifold can be found either underneath, inside or attached to the power control box.
Is there a reset button on a hot tub pump?
There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do I know if my hot tub has an airlock?
As mentioned above, the most common sign that your hot tub has an air lock is the jets not working when powered on. This can include nothing coming out of your jets when they are turned on or even a humming sound coming from the jets or pump.
What causes air lock?
The main cause of an air lock in pipes is when pockets of air are trapped by the flowing water, preventing the free flow of water. Also, cold water pipes have less pressure compared to hot water pipes; as a result, it’s mainly hot water pipes that are affected by air locks.