Table of Contents
If the pilot doesn’t relight, if it goes out right after lighting or if it goes out repeatedly, by far the most common cause is a bad thermocouple. The good news: You can usually replace a thermocouple for minimal cost and in less than an hour.
What does it mean when your pilot light won’t light?
Common Reasons Your Furnace Pilot Won’t Light There are several possible reasons why your gas furnace pilot won’t light: an ongoing draft, a faulty thermocouple, an accumulation of dirt, or an inefficient supply.
What causes the pilot light to go out on a hot water heater?
Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame. In either case, the thermocouple will struggle to sense the pilot light and stop the gas supply.
How do you clean a thermocouple on a water heater?
Clean the thermocouple – using the emery cloth sandpaper, sand the ends of the thermocouple and then give it a finishing touch with the lint-free cloth. Hopefully, you can get to the ends of the thermocouple without having to detach it from the assembly, but you may have to do that.
How do I know if my thermocouple is broken?
If you can’t get the flame to light at all, and you’re sure the gas is on, there’s probably an obstruction in the pilot tube. If the flame lights and goes out when you release the gas control knob after holding it in for the recommended 20 to 30 seconds, that’s the sign of a thermocouple malfunction.
What do you do when your pilot light goes out?
Your pilot light relies on your natural gas to stay aflame, so if your gas is shut off, your pilot light will go out. Simply turn your gas back on and either relight your pilot light yourself or call a professional.
How much does it cost to replace a thermocouple on a water heater?
Thermocouple – $20 to $150 The thermocouple is an apparatus that senses whether the pilot light is lit and triggers the gas control valve. Repairs typically cost about $150 to have it done professionally, though a new thermocouple itself only costs about $20 on average.
Can you bypass a water heater thermocouple?
Realistically, you have just disabled the thermocouple, but you can also reach in and unclip it from its holding bracket where it meets the pilot light. In most cases it will be held on with a gravity clip, but some are held on with a screw that must be removed with a small screwdriver.
How do I know if my thermocouple is bad on my water heater?
If the pilot lights but the flame goes out as soon as you release the button after holding it for 60 seconds, then the thermocouple is bad. It’s possible to replace the thermocouple without removing the burner assembly, and many repair people do this.
How long does a water heater thermocouple last?
Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
Can you replace a thermocouple yourself?
1 cause of pilot lights that won’t stay lit is a worn-out thermocouple. It’s easy to replace and a new one costs $5 to $10. Then detach the thermocouple from the burner and take it with you to the home center or hardware store to ensure you buy the right replacement.
Can you manually light a gas water heater?
Lighting a water heater is simple, no matter what type you have. Most newer models of gas water heaters have a simple ignition switch. In just a few steps the water heater is lit, no problem. If you’ve moved into an older house, though, you many have the kind of water heater that needs to be lit manually.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
Should the water heater be on pilot or on?
You should set the water heater to “pilot”. If, however, your water heater is also the boiler for your central heating, then you’ll want to leave the heating running as normal so that your house doesn’t get damp as a result of cold and condensation.
What is the most common problem with water heaters?
Water leaks are perhaps the most common type of water heater issue you’ll face. Any water heater will start to leak eventually, as by nature water will eventually corrode your tank and create microscopic cracks or fractures. However, this isn’t always a sign that your tank is what’s leaking.
Can a water heater explode?
Water heater explosions are terrifying, and they can happen. Anything that causes excess pressure on your water heating system, such as a poor anode rod, or a lot of sediment buildup, can all cause your water heater to explode. A gas leak can also cause your water heater to explode because it is a tremendous fire risk.
How much does it cost to replace water heater pilot?
Pilot light replacement or lighting cost Water heater pilot light replacement costs $50 to $200. The pilot light produces a flame to ignite the gas burner. Plumbers charge $45 to $150 per hour to reignite the pilot light, and the task typically takes 1 hour or less.
How do you jump a thermocouple?
To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.
