Table of Contents
Drain Hose Is Obstructed An obstructed drain hose is one of the most common reasons a Maytag washer won’t drain. Both kinks and blockages can obstruct the hose, preventing proper draining. However, if your washing machine is leaking, the kink may have damaged the hose, necessitating replacement.
Why is my Maytag washer not draining or spinning?
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
Why is my Maytag top load washer not draining?
Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.
Why does my washer wash but not drain?
There are a few possibilities why your washing machine won’t drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do you get water out of a Maytag washer?
5 Easy Steps to Get Water Out of Your Washer Step 1: Power It Down and Turn Off the Water Supply. Start by powering down your machine. Step 2: See If You Can Drain the Drain Hose. Step 3: Check Out the Drain Pump. Step 4: Drain the Interior Manually If Needed. Step 5: Know When to Call a Professional.
How do you force drain a Maytag washer?
Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections. Scoop out any remaining water in the washer drum. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.
Why won’t my washer drain and spin?
If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.
How do you drain a Maytag top load washer?
How to Drain a Top-Loading Washing Machine STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one. STEP 2: Locate the drain hose and water supply hoses. STEP 3: Drain the washing machine of water. STEP 4: Remove a drain hose clog. STEP 5: Remove a drain pump clog.
Where is the drain filter on a Maytag top load washer?
In top-loading machines the filters are in the center of the agitator tube. They can be removed by taking off the agitator cap and pulling the filter upward. Lint and debris can then be removed by hand before replacing the filter.
Where is the coin trap on a Maytag top load washer?
Inside the center agitator: If you have a top-loading washer, inspect the center agitator. The cover may be removable, revealing a lint trap inside. At the end of the drainage hose: A small mesh screen may be fitted onto the end of the hose that drains water out of the machine.
How do you force a washing machine to drain?
If not, follow these steps: Step 1: Turn off the power and lay down towels. For safety, unplug the machine. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
Why is there water under the drum of my washing machine?
Water In Bottom of Washing Machine Drum: Why It Happens Your lid mechanism is broken or not engaging fully. Your drain or hose is clogged. Your load was too large for a good spin cycle. Your washing machine’s sensors are damaged or old.
How do I know if my washing machine drain hose is clogged?
If the hose is clogged, it can prevent the water from being pumped out of the machine. To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
Why won’t my Maytag Centennial washer drain?
If your Maytag washer won’t drain or is continually draining, it is likely an issue with the drain hose or pump. Check that each is clear of any blockages that could be impeding water flow. In addition, check that the door lock is in working order and also that the water inlet valve is not damaged.
