Table of Contents
How do you fix a GE washer that won’t spin?
GE Washer Not Spinning Check the detergent type: Make sure you are using the right kind. Check the detergent level: Check the level of the water in the tub: Check the water type: Make sure the water is at the correct temperature: Check the agitator: Check the fabric type: Check the spin cycle:.
What causes the washing machine not to spin?
Normally, your washing machine won’t go into a spin cycle until it’s been drained. The drainage hose may become clogged with debris from your clothing, or it could be kinked. If the hose is kinked or crushed, it will likely need to be replaced.
How do you reset the spin cycle on a GE washer?
Unplug the washer for one minute, then plug the washer back into the electrical outlet and lift and lower the lid six times within 12 seconds. This will reset the motor and you should be able to start the cycle.
Why won’t my GE washer agitate or spin?
Common solutions for: GE Washer won’t spin or agitate. Inspect the drive belt to determine if it is broken or if it is loose on the pulleys. If the drive belt is broken or loose, replace it. If the washer is overloaded, the motor coupling will fail in order to protect both the motor and transmission.
How do you troubleshoot a GE washing machine?
How to Troubleshoot a GE Top Load Washer Check the amount of detergent you have put in the washer. Examine the GE top load washer’s drain hose for leaks. Check the water connections to your GE top load washer. Check whether the GE top load washer lid is closing firmly. Check the load in your GE top loading washer.
Do GE washers have a reset button?
To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
How do I reset my GE washer?
Steps to reset GE Hydrowave Washer: Switch OFF Washer for 60 seconds. Plug the washing machine back in. In less than 30 seconds, open and close the lid of the washing machine six times. This must be done within 12 seconds period. The washer lid must be raised at least two inches.
Does unplugging a washer reset it?
Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.
Why does my washer agitate but not spin?
If your washer won’t agitate but spins, a broken agitator may be to blame. The output shaft of the transmission is splined to the agitator to secure it in place. Over time, some of the components of the agitator can wear down or break with normal usage, causing your washing machine not agitating issue.
Why won’t my GE washing machine fill with water?
Machine Won’t Fill If your washer won’t fill, check the hot and cold faucets to make sure they’re both turned on fully. Check the fill hoses, which connect to the upper back left of most GE washers, and make sure the line has no kinks. If the problem persists, turn off the water and remove the fill hoses.
How do you force a GE washer to drain?
There may be a clog. Press Start to resume the cycle or you can select Drain & Spin and press Start. If water remains in the washer, check for a pinched or flattened drain hose. If you clear a clog, press START to resume your cycle or you can select Drain & Spin and press Start.
How do I put my GE front load washer in diagnostic mode?
To enter the LED and buttons test mode on a GE front load washer, rotate the control knob until t04 is displayed in the control panel then press start/pause to enter the test mode. This test mode will test to see if each button works and each LED will light. Each light should blink once in a loop.
How do I reset the lid lock on my GE washer?
Top Load Washer – Lid Lock Feature Make sure the washer is paused (press the Start/Pause button). During the spin cycle, this can take up to 3 minutes for the basket to stop spinning and allow you to open the lid. Unplug the washer for a minute to reset.
Why won’t my GE washer drain?
GE’s washer may have a clog in the hose, filter, or pump, which can cause the washing machine not to drain. Troubleshooting steps: To fix this, turn off the washer and unplug it from the power outlet. Then, remove any kinks in the hose and double-check that it’s connected to your GE washer properly.
How do I reset my GE washer gtw460asjww?
Plug the washing machine back in and then within 30 seconds, quickly open and close the lid six times. You’ll need to do this within a 12-second period. Raise the lid at least 2 inches and make sure it closes each time. This should complete the motor reset.
