Table of Contents
There are a few possibilities why your washing machine won’t drain. Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.
How do you fix a washer that won’t drain?
What to Do When Your Washing Machine Won’t Drain Perform a Master Reset. Unplug your washer for about one minute. Test the Lid Switch Assembly. See if the Drain Hose is Kinked. Check the Drain Hose or Pump for Clogs. Clean out the Coin Trap. Check the Water Level Control. Schedule Washing Machine Repair.
How do you force a washing machine to drain?
If not, follow these steps: Step 1: Turn off the power and lay down towels. For safety, unplug the machine. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
What causes a washing machine to not spin and drain?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do I know if my washing machine drain hose is clogged?
If the hose is clogged, it can prevent the water from being pumped out of the machine. To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
How do you position a washing machine drain hose?
In order for the drain hose on your Top Load washer to function properly, the drain must be at least 30″ up from the floor and less than 8 feet high. In order for the drain hose on your Front Load washer to function properly, the drain must be at least 24″ up from the floor and less than 8 feet high.
Can a washing machine drain into 1 1 2 pipe?
Drain and Trap Requirements A 2-inch drain pipe is required for all washing machines. The former requirement of 1 1/2-inch pipe is not enough to handle the fast drainage of modern washers. As with all plumbing fixtures and appliances, a washing machine drain pipe must also contain a P-trap.
Where does a washing machine drain?
Washing machines drain into what is called a standpipe. A standpipe is a vertical piece of pipe with an elbow on the bottom. The elbow remains filled with water, preventing sewer gas from backing up into your laundry area.
How do you know if your washing machine drain pump is broken?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
How do I know if my washing machine pump is broken?
Check the pump pulley by removing the pump from the washer and trying to rotate it by hand. If the pulley doesn’t turn freely and is frozen or stiff, replace it. Also, if the agitator is moving but the tub isn’t, this is a sign the pump is dying. For front-loading washers, do not attempt to open the door mid-cycle.
How do you unclog a drain pipe?
If you find yourself with a clogged drain line, hot water, vinegar, and baking soda can serve as an inexpensive way to unclog it. Pour the hot water down the drain first, then baking soda, then vinegar, followed by more hot water after you’ve let the mixture sit in the drain for 10-15 minutes.
Can I use PVC for washer drain?
Kitchen sink drains use PVC pipes with washers, called slip-joints or slip-jam-nut couplings. Once the nut is screwed on tight, the pressure from the connection forces the washer up against both pipe ends or the pipe and the drain end to create a watertight connection.
How long should a washing machine drain pipe be?
For a top load washing machine, 5” of the hose will go inside the drain pipe. And for front load machines, the length should be 7”. The universal diameter for the drain hose is 1-1 ¼ ”.
Does a laundry drain need a trap?
Your washing machine needs a trap on the drain line because the drainpipe connects to the sewer or septic system. This means the pipe can be a conduit for sewer gas to drift up into your home. Every time your washer drains, some of the water that flows into the pipe is caught in the trap.
How much does it cost to replace a washing machine pump?
The price of a new washing machine pump is $25 to $40 on its own, not including labor. When hiring a professional, repair prices range from $200 to $450.
How do you diagnose a washing machine problem?
Washer Troubleshooting Guide Check that the washer is plugged in securely. Check the circuit breaker or fuse box. Test the outlet for current. Check that the water supply valves are turned on. Inspect the filter screens. Test for overheating. Test the water level switch. Test the timer control.
