Table of Contents
How wide should my binding strips be?
Cut enough strips (bias or crossgrain) to go around the quilt plus 8″ for cornering and seams. Strip width can vary from 2″ to 2 1/2″ and even wider if you prefer a larger binding than the traditional 1/4″ width. Quilt binding strips are generally sewn together with a diagonal seam for the most inconspicuous joining.
What is a Faced binding?
The Faced Binding is a neat way to finish the edges on a large wall quilt. The quilt in this example measures 32″ w x 48″ h. Add the backing to your quilt top and machine stitch the quilt.
How long should binding strips be?
Sew strips together end-to-end on a 45 degree angle into one long strip using diagonal seams. Press seams open to reduce bulk. Fold strips in half lengthwise with wrong sides together and press. The entire length of your binding should be equal to the perimeter of the quilt plus 15 to 20 inches.
Do you bind a quilt before quilting?
Binding a quilt is the final step in finishing. Before you bind, you need to somehow “quilt” your quilt. This means to attach the front and back, with batting in between. I usually machine quilt (or have someone else do it) my quilts these days.
Should quilt binding be cut on the bias?
For a square quilt straight grain binding, meaning fabric strips cut cross grain or length-wise grain, will work well. If, however, you’re binding a quilt with curved edges, you’ll want to cut bias strips for your binding. The stretch in the bias makes it easier to maneuver the binding around the quilt’s curved edges.
What is a Faced edge?
Faced neckline and armhole edges are smooth, crisp, and well supported. Facings provide a smooth, clean finish to garment edges, typically at the neckline, armholes, and center-front openings.
What does it mean to face a quilt?
Art Quilter, Robbi Joy Eklow, shares her method for facing a quilt, a finish that gives the edges of a quilt a clean look without the frame of traditional quilt binding. A facing is similar to a binding on a quilt, except that it’s turned completely to the back so there is no visual line around the edge of a quilt.
What is the difference between facing and binding?
Binding is done by a piece of fabric either cut on grain or crossway while facing is cut from fabric.
Why is the back of my quilt puckering?
Puckers in the quilting usually result from a basting process where either the backing wasn’t spread and secured properly or too few safety pins were used or things shifted as the quilt was positioned under the needle and quilting began.
Do I need bias tape?
Bias tape is perfect for a decorative finish on a curved edge because the bias will bend and ease around the curve. A straight-grain strip will not curve without kinks and warping. Bias is used in many quilting techniques and sewing projects.
How close to the edge do you quilt?
If the outside border is made of pieced blocks, for example, flying geese, stay-stitch all the way around the edge of the quilt at 1/8 of an inch. This will prevent the seams from pulling apart. Stitching within 1/8 inch will fall inside the binding.
What is the difference between bias tape and binding?
Now that you’re an expert on the differences between tape, facing, and binding, we’ll cover some tips and tricks for getting a great finish. This is because while bias facing turns the seam allowance inward, bias binding simply wraps around the raw edge.
Which way do you cut fabric for binding?
Cut crosswise strips the desired width, cutting enough strips to equal the total length needed. Use a fabric’s crosswise straight grain rather than its lengthwise grain for more give and elasticity. 2. Position and pin the strips perpendicular to one another with the raw edges aligned and right sides together.
Why is facing important?
Facing makes a garment look professionally finished with the seams well hidden inside the folds of the facing. Shaped facings are cut to match the outside shape of the piece to provide a neat finish, and are often cut from the same pattern pieces.
What is Understitch sewing?
An understitch is sewn along the edge of the lining or facing nearest the armhole or neckline and works to secure the lining or facing to the seam allowances which in turn keeps everything neatly tucked inside the garment instead of poking out and being visible from the right side.
How wide should facing be?
How wide should a facing be? A facing can be very narrow, for example 2.5cm (1in), or up to 10cm (4in) wide or even wider. Most are around 4-5cm (1½- 2in) wide. Facings are usually cut the same width all the way around, but sometimes a back neck facing is cut deeper at the centre back.
What do darts do in sewing?
Darts are folds (tucks coming to a point) and sewn into fabric to take in ease and provide shape to a garment, especially for a woman’s bust. They are used frequently in all sorts of clothing to tailor the garment to the wearer’s shape, or to make an innovative shape in the garment.
Do facings need interfacing?
Interfacing should always be used when facings are called for in a pattern–even if the pattern does not require interfacing. The interfacing prevents stretching or sagging of the neckline or sleeves, acts as reinforcement for the area, and gives the garment a smooth but firm body.
Do you top stitch facing?
Topstitch all the way around the outer edge of the facing, sewing it to the opening. This step secures the facing in place so that it doesn’t flap around when you wear your garment.
What is the edge of a quilt called?
Borders: Strips of fabric that frame the edges of the quilt. You can have one or many borders in a quilt top. You may also have borders surrounding your quilt blocks, also known as sashing, or as part of quilt block design.
What is quilt backing?
Quilt backing is the bottom layer of a quilt sandwich. They can be made from large cuts of coordinating fabric (such as 44″-wide quilting cotton ) that are stitched together to fit your quilt, or they can be cut down from 90″ or 108″ cuts of quilting cotton that are specially designed for backing large projects.
