Table of Contents
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do you force a Maytag washer to drain?
Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections. Scoop out any remaining water in the washer drum. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.
Why is my Maytag top load washer not draining?
Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.
Why does water stay in washing machine drum?
The outer drum is stationary and contains the water, the inner drum rotates and holds the clothes for washing and spinning. The water doesn’t drain out the bottom because the regular drain pipe is above the top of the drum – the water will stay until the drain pump is turned on during the drain and spin cycles.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
Where is the coin trap on a Maytag top load washer?
Inside the center agitator: If you have a top-loading washer, inspect the center agitator. The cover may be removable, revealing a lint trap inside. At the end of the drainage hose: A small mesh screen may be fitted onto the end of the hose that drains water out of the machine.
Where is the drain filter on a Maytag top load washer?
In top-loading machines the filters are in the center of the agitator tube. They can be removed by taking off the agitator cap and pulling the filter upward. Lint and debris can then be removed by hand before replacing the filter.
How do you drain a Maytag top load washer?
How to Drain a Top-Loading Washing Machine STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one. STEP 2: Locate the drain hose and water supply hoses. STEP 3: Drain the washing machine of water. STEP 4: Remove a drain hose clog. STEP 5: Remove a drain pump clog.
How do I clean the drain pump filter on a Maytag top load washer?
The quickest way to clean out your filter is to remove it from the unit and soak it in hot water, loosening any clog or trapped residue. If the filter cannot be removed, clean it out with brush. Some filters are disposable, so instead of cleaning them you can just throw them away and put a new one in place.
How do you force a washing machine to drain?
If not, follow these steps: Step 1: Turn off the power and lay down towels. For safety, unplug the machine. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
How do you fix a washing machine that keeps draining?
Solutions Turn the machine off at the powerpoint. Check that the drain hose is not kinked or bent. Now, remove the drain hose from the back of the machine. Run some water through the hose to force the clog out. Once water is steadily running through the washer drain hose, re-attach it to your machine.
Can you pour Drano down washing machine drain?
Can I put Drano down my washing machine drain? Yes. Drano or any drain cleaner can be used to unclog your washing machine drain, but make sure you run your washer without a load of laundry before normal use.
How do you know if your washing machine drain pump is broken?
Put your finger into the drain outlet and feel the impellers if the pump freely turns. One or more of them may be broken. If so, you’ll be able to feel them while you’re turning the pump flywheel with your other hand. You also may see broken pieces of plastic in the bottom of the pump housing.
How do you know if your washing machine drain hose is clogged?
The surest and most obvious sign that your washing machine’s drain hose is clogged is if you notice that the water in your machine isn’t draining away properly. Many people first notice this after putting their laundry on the spin cycle and realizing that it’s still soaking wet at the end of the timer.
What does the Maytag extra power button do?
With the push of a button, Maytag fights both in a single load. The Extra Power button boosts stain-fighting performance on any wash cycle with a dual-temperature wash.
Does my Maytag washer have a coin trap?
That’s why the standard design of a washing machine always includes a filter or coin trap along the washer’s drainage. That’s true for any brand of washer, including the Maytag model that you have at home.
