Table of Contents
If you own a Honeywell thermostat, the blank screen could be an indication of a furnace door that wasn’t completely closed. These thermostats are programmed to shut off entirely if a furnace door is open. To rule this out, double-check to make sure your furnace door is fully closed.
How do you reset a Honeywell thermostat when the screen is blank?
Reset Your Honeywell Thermostat Turn off your Honeywell Thermostat switch. Open the battery slot by pressing the door down and sliding it out. Once you have opened the battery slot, slide the batteries out. Re-insert the batteries, but put them in a reversed position.
Why did my thermostat screen go blank?
This is commonly due to restricted airflow because of broken or dirty parts in the HVAC system. A failing fan motor can cause your electrical components to pull in more amperage than usual, tripping the high-limit switch. Any of these could cause a blank thermostat screen.
Is there a reset button on a Honeywell thermostat?
If you press and hold the MENU button, a reset option will appear. Select the RESET option and confirm with the OK button. Your Honeywell T5, T5+, or T6 thermostat is now reset. A faster way to reset a Honeywell thermostat without a reset button would be to switch off the circuit breaker’s power.
Does a Honeywell thermostat have a battery?
The battery compartment on a Honeywell thermostat is located on the side of the device. To remove it, first push the tab on the top of the thermostat. Then pull it to remove the compartment — it should slide right out.
Does Honeywell thermostat need batteries?
Not all Honeywell thermostats run on batteries. However, if your model has an LED display, chances are it does! Just like any device that runs on batteries, you need to have these batteries changed from time to time. With most Honeywell thermostat models, you need to change the batteries only once a year.
What causes no power to thermostat?
No power to thermostat could also be caused by old batteries. When it comes to the controls and display on your thermostat, these are typically powered by batteries. Over time, these will wear out and stop working. If it has been a while since you changed these batteries, this could be your problem.
What causes thermostat to lose power?
The power is out or a circuit breaker has tripped The power loss could also be the result of a tripped circuit breaker that powers the air conditioner or heater. Many thermostats run on low voltage sent from the transformer on the HVAC system; if the transformer loses power, so will the thermostat.
Why would a Honeywell thermostat stop working?
Look at the wiring and check if anything is loose, broken, or disconnected. Also, check to see if everything is clean. If the inside of your thermostat is filthy or there is loose wiring, that could be your problem.
How do I fix an unresponsive Honeywell thermostat?
How to unfreeze Honeywell thermostat (Step-by-step) Step 1: Remove your thermostat from wall. Step 2: Pull the batteries out. Step 3: Pull the cover out. Step 4: Remove both the circuit board and screen. Step 5: Disconnect the circuit board. Step 6: Restore the connection.
How long do Honeywell thermostats last?
The average lifespan of a thermostat is at least 10 years. Dust and aging wiring can cause the thermostats to malfunction after a decade.
Why is my Honeywell thermostat not turning on heat?
A Honeywell thermostat won’t turn on the heat because of faulty sensors, improper installation, tripped circuit breakers, etc. The heat not turning on issue on your Honeywell thermostat may be fixed by resetting the Thermostat.
What happens when thermostat battery dies?
When your thermostat batteries die, you will see a black screen, the thermostat will stop working, and the heating or cooling units will not work. If, after the change of batteries, the thermostat and the heating and cooling systems start working, then everything should be back to working as normal.
How do I know if my thermostat needs a battery?
Check the screen: Check the screen of the thermostat and make sure that it is lighted. A blank or unlighted screen could indicate a thermostat failure. Check the batteries: Many modern thermostats rely on battery power to operate. If the screen is blank or unlighted, a battery change could solve the problem.
How do you reset the battery on a Honeywell thermostat?
Here’s how: Power off the thermostat and remove the batteries. Put the batteries in the wrong way, with negative to positive and positive to negative. Wait ten seconds and put them back in the correct way. Your thermostat will be reset to factory settings. Be sure to reprogram your thermostat to your normal schedule.
Can a thermostat work without batteries?
The good news is, some thermostats can work without batteries. Such thermostats still need a source of power, so they rely on line voltage or a C-wire. The Nest thermostat can even power cycle your HVAC system to maintain a charge on it’s inbuilt battery.
How do I get my Honeywell thermostat to work?
A few tips and tricks you may want to try to get your Honeywell thermostat to turn on include: Replace the Batteries. You should start with the easy and obvious solution first. Check the Air Filter. Check the Circuit Breaker. Check the Wiring for Any Loose Connections. Reset Your Thermostat To Factory Settings.
How do I restore the power to my thermostat?
How to Reset Your Thermostat After a Power Outage Turn off your thermostat. Before doing any other troubleshooting, start by finding your thermostat and turning it off. Locate and reset circuit breaker. Wait 30 minutes. Turn the thermostat back on.
How do I know if my Honeywell thermostat is bad?
Let’s delve into it. Your HVAC Keeps Turning On or Off. Faulty Thermostat Readings. Suspiciously High Energy Bills. Constant Temperature Shifts. Thermostat Is Too Old. Thermostat Fails to Respond to Changed Settings. Your HVAC System Short Cycles.
