Table of Contents
DIMENSIONAL LUMBER: In the past, when a timber was called a 2×4 [or “two-by-four”], it actually measured 2 inches by 4 inches. Because of this extra milling, a 2×4 no longer measures a full 2 inches by four inches. Instead, a 2×4 is really only 1 1/2″ by 3 1/2″.
When did 2x4s stop being 2×4?
This pressured further compromise because thinner 2x4s were a way to compete in price with wood alternatives. Size standards, maximum moisture content, and nomenclature were agreed upon only as recently as 1964. The nominal 2×4 thus became the actual 1½ x 3½, imperceptibly, a fraction of an inch at a time.
Why is dimensional lumber not actual size?
The “nominal” cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.
Why is a 2×4 actually 1.5 x3 5?
The 2×4 refers to the rough-cut green wood: it shrinks during drying, then the dried wood is planed smooth, so the finished lumber is supposed to end up at 1.5″x3. 5″. While it doesn’t really shrink that much, the mills get more usable finished 2×4’s from a given tree if they cut them slightly smaller to begin with.
Why is lumber a half inch short?
The simple reason why 2×4 is not 2 inches by 4 inches is that lumber mills trim off rough or warped surfaces of a 2×4 to give it a more polished and finished look. By planning the lumber on all four sides, the original 2×4 is now reduced to 1 ½ inches by 3 1/2 inches.
What do they call a 2×4 in Europe?
I cant speak for the hole of europe, but at least in Norway a “2×4″ is 48×98 mm. If you go to a lumberyard, you buy 48×98 as everything is measured in metric, but in the daily speach most people still use the term 2×4, 2×8 aso. The Inch measurement is in use as long as we speak about size on TV(40″) and cartyres (15”).
When did lumber dimensions change from actual to nominal?
Early concepts called for rough lumber to be of full nominal size, often in the dry condition. After World War I, the increasing demand for construction lumber led to the first national size standard in 1924. This was revised in 1926, 1928, 1939, and 1953, while still another revision is proposed for adoption in 1964.
Why is lumber smaller than the size it says?
Typically, that rough cut is smaller than the nominal dimensions because modern technology makes it possible to use the logs more efficiently. For example, a “2×4” board historically started out as a green, rough board actually 2 by 4 inches (51 mm × 102 mm).
What is the difference between nominal and rough lumber?
Rough sawn lumber has a very rustic appearance, which is a desirable look for some projects. After it is planed, the piece of lumber no longer has its nominal dimensions, for it has been reduced in size. It is stilled referred to by its nominal size, such as the 2×4, but its actual size is now 1 1/2” by 3 1/2″.
Why do 2x4s have rounded edges?
2×4 have rounded edges as it’s very beneficial to the wood itself and those working with it. They reduce the number of injuries like unwanted splinters during the handling and manufacturing process and also ensure that the lumber stays looking its best all throughout until the customer sees it.
What is the difference between dimensional lumber and studs?
Structural light framing is 2-inches to 4-inches thick and 2-inches to 4-inches wide. Dimensional lumber and studs are 2-inches to 4-inches thick and 2-inches to 4-inches wide. Structural joists and planks are 2-inches to 4-inches thick and 6-inches wide. Appearance framing lumber is 2-inches wide and 1-inch thick.
What is the longest 2×8 you can buy?
In general, a 2×8 will span 1.5 x 8, so 12-feet. Based on all factors though, a 2×8 joist span is 7′-1” to 16′-6”, and a rafter 6′-7” and 23′-9”.
Are 2×6 really 2×6?
In North America, the 2×6 size is actually referring to the lumber’s “nominal” dimension. A 2×6’s real or true dimension is 1.5″ x 5.5″ – within the industry it is referred to as its “actual” size. The nominal size is used when discussing lumber nearly 100% of the time! Same for 1×4, 2×4 and 4×4 etc.
What does it mean when someone calls you a 2 by 4?
(slang) Small in size; boxed in or cramped. A two-by-four apartment. adjective. 2.
What does a 2×4 actually measure?
The true measurement of a 2×4 is actually about 1.5×3. 5. When the board is first rough sawn from the log, it is a true 2×4, but the drying process and planning of the board reduce it to the finished 1.5×3. 5 size.
What do they call a 2×4 in Canada?
In Canada, where we adopted the metric system in the early 80s, we call them 2x4s.
What is a 2×4 in Australia?
This is similar to this question about metric measurements. In Australia, a common measurement is 90mm x 45mm for timber. A 4×2 would be (approx) 100mm x 50mm but, as I understand it, that is the milled rather than final measurement.
What is a 2×4 in UK?
2″x4″ timber is nominally 47mm x 100mm but is “regularised” with 3mm off the thickness and 5mm off the width, so it ends up being around 44mm x 95mm (may be nearer 45mm on the width).
