Table of Contents
If your Maytag Washer keeps filling or won’t fill up with water, you should check your water for improper installation or kinks in your water supply lines, inlet valves, and drain hose. These issues can also signify a faulty part in your household appliance, which may need to be serviced or replaced.
How do I fix the low flow on my Maytag washer?
LF in the display Check the water inlet hoses to be sure they are not clogged or kinked. You may also need to check the screens on the washer water inlet valve. This means shutting off the water supply, and disconnecting the water inlet hoses from the washer.
How does Maytag washer sensing water level?
When the Start/Stop button is pressed, and the Water Level knob is set to Auto Sensing, the washer will fill and begin sensing to determine load size and balance. Once sensing is complete, the washer will fill to the appropriate level for the detected load size and then begin the wash phase of the cycle.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
Why does my washer say low flow?
If you only notice low water pressure when using the hot water setting, then you probably have a clogged hot water line (or vise-versa for cold water). The easiest solution to this problem is to replace the clogged line with a new one. Water lines can be purchased either online or at most major home improvement stores.
What does low flow mean on washer?
Troubleshooting and Repair – Lo FL Error Code – WFW75HEFW. The Whirlpool washer Lo FL error code is displayed when water is not detected entering the washer or it’s not filling the washer fast enough.
Why won’t my Maytag washer drain and spin?
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
What are the codes for a Maytag washer?
Error Codes in my Maytag Front Load Washer Error Code Error Sud or Sd There are too many suds in the washing machine. F5 E2 The door is not locking properly. F7 E1 Indicates a motor speed sensing error, F8 E1 or LO FL The washer is sensing a low flow of water.
How do you reset the lid lock on a Maytag washer?
Once paused, the lid automatically unlocks to allow changes to the current load. Touch “Cycle Signal” near the front-loading washer’s LCD control panel to deactivate the washer’s lock controls. Push “Start/Pause” to temporarily halt the washer’s current cycle, and wait for the indicator light below “Pause” to light up.
Why does my washer not fill with cold water?
If the washer will not fill in the rinse cycle, you may have a bad water supply, failed valve or a wiring problem. Turn your cold water supply valve off. Disconnect the cold fill hose where it connects to the back of the washer. Check for a clog or debris on the inlet water screen on the back of the washer.
Why does my washing machine take so long to fill with water?
When your washing machine is filling up slowly with water or sometimes no water flows at all, it is usually clogged inlet screens, water valves not being fully open, or a solenoid valve water inlet issue. One of the water temp selections will be slow to fill and the other will flow as normal.
Can I run a washing machine with low water pressure?
Because older machines fill in this gradual manner, low water pressure does not affect the washer. However, without high enough water pressure, modern machines might not allow enough time to fill. Instead of switching off during the fill part of the cycle, the motor keeps running and the clock keeps ticking.
Is water pressure important for washing machine?
To fill water into the washing machine correctly in recommended time period, the water pressure must be between 20 and 116 psi. Water pressure less than 20 psi can cause water valve failure or prevent the water valve from shutting off completely. A fill time limit is built into the controls of your washing machine.
What does FS mean on Maytag washer?
What could that mean? The Maytag washer code F5 is an alert that tells you the lid can’t lock. There could be some clothing or other obstruction in the lid preventing it from locking. This is one of the simplest problems to fix.
Where is the water level valve on a washing machine?
The water level switch is a pressure activated switch that is used to determine the correct water level in the tub. This part is normally located behind the control panel and will have a hose or air dome tube that connects it to the tub.
How do you force drain a Maytag washer?
Here’s how to manually drain water from a Maytag washing machine: Pull the washer away from the wall and turn off its power and water connections. Scoop out any remaining water in the washer drum. Unhook the drain hose from the wall or sink drain and empty residual water into a bucket.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
Where is the coin trap on a Maytag top load washer?
Inside the center agitator: If you have a top-loading washer, inspect the center agitator. The cover may be removable, revealing a lint trap inside. At the end of the drainage hose: A small mesh screen may be fitted onto the end of the hose that drains water out of the machine.
