Table of Contents
What would causes a washing machine not to fill with water?
The hot and cold water hoses that lead to your machine should have a filter screen to catch any large particles that might be coming through the lines. Sometimes these screens can get clogged, which keeps water from flowing properly. This is probably the most common reason for a washer not filling with water.
How do I get more water in my Whirlpool washer?
If you would like the machine to automatically sense the appropriate water level for the load size and type, turn the Water Level knob to the Auto Sensing setting. If you would like to add the maximum amount of water to your wash cycle, turn the Water Level knob to the Deep Water Wash setting.
How do you reset a Whirlpool washing machine?
Turn off the washer on the control panel. Unplug the washer for twenty seconds. Turn on the washer. If the process has worked, your washer will now be reset.
How do I fix the water level in my washing machine?
How to Adjust a Washing Machine Water Level Switch Unplug the unit from the wall. Remove the screws from the control panel. Find the back of the water level switch. Pull the wires off the water level switch to expose the connectors. Follow the tube down the outer tub.
Why does my Whirlpool washer say detergent low?
Detergent Level Low – This will light (yellow) if there is enough detergent in the Load & Go™ cartridge for only a few more cycles.
How do I reset my Whirlpool top load washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I reset my Whirlpool load and go?
Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
Where is the water level switch on a Whirlpool washer?
Look for the water level switch on the right side of the cabinet toward the back of the washer. The round water level switch attaches to the side of the cabinet. A rubber tube connects the water level switch to the washtub.
What is water level sensors?
Level sensors are used to detect the level of substances that can flow. Such substances include liquids, slurries, granular material and powders. Such meaurements can be used to determine the amount of materials within a closed container or the flow of water in open channels.
Why does my Whirlpool washer say add garment?
The “Add Garment” light on the display panel is a special feature of the Whirlpool Duet washing machine. It lets you know when you can add items to an already started load of laundry. In some instances, the machine will leave the light on or even leave the door locked with the light on at the end of the cycle.
What is the problem with Whirlpool washing machines?
The extra current that runs through the machine when the heating element is on can cause the door locking system to overheat. The company said the issue had been identified by its safety team, but had led to fires, although none had been significant enough to cause more than minor damage or cause any serious injuries.
How do I reset my top load washer?
Motor Reset Procedure: Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.
Why is my Whirlpool washer not working?
One reason your appliance may not start is that it has simply come unplugged or that the outlet that it is plugged into has tripped your home’s main circuit breaker. If you notice a tripped breaker, leave the breaker off and carefully inspect the electrical outlet and power cord for any sign of a problem.
Why does my Whirlpool washer stop mid cycle?
Whirlpool Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
What does the code F28 mean on a Whirlpool washer?
The digital display on the Whirlpool Duet washer, at times, will display an error code to alert you of a problem with the washer. An F28 error code is a common problem that means there is a communication problem with the central control unit. This problem is generally solved by essentially rebooting the control unit.
What does whirlpool diagnostic mode do?
The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
What would make a Whirlpool washer not spin?
If your Whirlpool washer Not Spinning well, you need to check the pump. It could be clogged with debris or defective and needs to be replaced. To check the pump, disconnect the drain line and remove the back panel of your machine. Check for debris with a flashlight, or check with a special tool.
