Table of Contents
If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.
Why does my heater turn off after a few minutes?
Low airflow When the exchanger heats up to the maximum temperature, the furnace shuts off after a few minutes. The furnace won’t be able to pull fresh air into the blower if the air filters are clogged with dust, pet hair, and other debris. You should also make sure to open all of your air supply vents.
Why does my natural gas wall heater keep going out?
The heater won’t operate properly if the pilot flickers, is too weak or goes out, and the cause could also be blockages in the pilot tube. Another cause of a weak pilot is a faulty thermocouple. It’s a heat sensor placed next to the pilot flame that signals the gas valve to stay open when the flame is burning.
Why does my electric heater keep turning off?
Here are some common reasons that portable electric heaters shut off: The thermostat on the heater is not set high enough. The heater needs to be reset due to an overheat situation. If the unit has tip-over safety protection: To reset, simply place the heater in an upright position on a level surface.
Why won’t the pilot stay lit on my wall heater?
The Pilot Won’t Stay Lit A pilot that won’t stay lit could be the result of a blockage in the pilot tube. Turn off the gas, clear the tube with compressed air, and relight the pilot. If that doesn’t work, you may need to call a repairman to come and install a new thermocouple.
Why does my furnace keep shutting off after a few seconds?
A common reason a furnace short cycles is because the heat exchanger, the part that heats your air, is getting too hot due to a lack of airflow. Once the heat exchanger overheats, it trips the high limit switch, which shuts the furnace down to protect it.
Where is the reset button on a furnace?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
Why is my heat not shutting off?
One of the most common issues is the thermostat. The wiring, switches, or heating sensors can fail on your unit. A faulty check valve could be the cause of this type of heating system to fail. If your heating system will not shut down, then you need to call a professional technician for help.
How do you reset a gas wall heater?
Turn the power back on and then the main gas supply. Locate the reset button. It is labeled, sometimes in red. Press and hold the reset button for 30 seconds.
Why does my wall heater turn on by itself?
The problem of short cycling can be caused by a faulty thermostat. The placement of the thermostat is important. It can sense that the temperature in your home is too warm if it’s too close to another heat source.
Do wall heaters turn off automatically?
If an oversized gas wall heater is installed in your home, the system will likely turn off on its own once the room is sufficiently heated. It would then automatically turn on once the need for heating is required.
Why does my electric heater keep turning on and off?
The heater turning on and off excessively could be the result of the thermostat being placed in the wrong spot. If it’s installed near a heat-producing appliance, like a kitchen stove, it could confuse the unit into thinking the house is warmer than the actual temperature.
How do you reset an electric heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
How much does it cost to replace a thermocouple?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.
Can you clean a thermocouple?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up.
How do you check if a thermocouple is working?
Place one test lead on the side of the thermocouple and the other to the end that screws into the gas valve. If the thermocouple has proper continuity, a small resistance reading should be visible on the multimeter. Many multimeters also indicate continuity with an audio alert.
Why does my furnace turns off before reaching temperature?
A lack of airflow can cause your furnace to stop heating before reaching the set temperature. Ensure there is nothing impeding airflow around your furnace, within your furnace and through your ducts. Inside your furnace should be clean and free of debris, especially around the blower motor and the heat exchanger.
How do you fix a short cycle on a furnace?
The easiest way to fix a furnace that is short cycling is to remove the flame sensor to clean it. Use a sponge or brush to remove the dirt from the sensor. After the part is clean, follow the manufacturer’s instructions to insert the flame sensor into the furnace.
Why is my furnace not staying lit?
Probably the most common issue when dealing with a furnace that will not stay lit or ignite consistently is a dirty flame sensor. The flame sensor acts as a communication vehicle with the circuit board and tells it when a flame is lit inside the furnace.
