Table of Contents
Common solutions for: Maytag Washer stops mid cycle If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
Why does my washer stop on the wash cycle?
If you find that your washer is routinely stopping during the rinse cycle, then it may be caused by a faulty water inlet valve. As it stops during the rinse cycle, the washer will stop in the middle of the wash. It could be faulty, or it could simply be an obstruction that needs to be removed in the valve.
How do I reset my Maytag washer?
The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
How do you fix a washing machine that stops mid cycle?
To fix a washing machine that stops mid-cycle, try a master reset by first unplugging the washing machine to reset the computer. After 1 minute, plug your machine back in, then open and close the door 6 times in 12 seconds to signal the computer to reset.
Why does my Maytag washer stay on sensing?
If your Maytag washer’s sensing light is stuck and will not move to the appropriate cycles, this is usually caused by a stuck or keypad. The keypad can occasionally become jammed or, if you have recently replaced a part on the washer, you may have forgotten to recycle the codes, which can lead to a stuck sensor light.
How do I find the error code on my Maytag washer?
The washer may take 20 to 30 minutes to stop spinning and drain, and will display this error code during that time. To remove the code, press pause or cancel button twice and the power button once. If the code is still displayed, unplug the washer or disconnect the power for one minute.
Why won’t my Maytag washer spin and drain?
A top load Maytag washer not draining may have a defective lid switch assembly. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch. Try depressing the lid switch with your finger to see if the machine drains and spins.
Why does my washer stop at sensing?
In case your washer has stopped midway with the sensing light flashing, and you are unable to access diagnostics, check if you can drain the water and use the spin function. If the water drains from the unit, but your Whirlpool Washer won’t spin, you may have a problem with the shift actuator.
Why is my washing machine stuck on sensing?
The sensing light begins to blink when a new wash cycle starts. While this is perfectly normal, if you notice that the light keeps blinking for too long, it means the washer is stuck on the sensing phase. This usually indicates an issue with the load size, sensor, a faulty equator, or clogged drain pump.
Does a Maytag washing machine have a fuse?
Maytag washers have a fuse in the lid-switch assembly. Maytag top-loading washers have a fuse in the lid-switch assembly. When you close the lid after adding the laundry and soap, the lid’s plastic switch contacts with the assembly underneath. Checking the fuse with a multimeter determines if it needs replacing.
How do I fix a Maytag washer that won’t turn on?
Here’s how to check your power connections: Perform a Maytag washer reset: Try unplugging the washer for 1 minute before plugging it back in to see if power is restored. Power cord: Make sure the power cord is free of damage and completely plugged into a working outlet.
How do I know if my thermal fuse is blown?
Touch the left multimeter lead to the left side of the thermal fuse; touch the right multimeter lead to the right side of the fuse. Keep an eye on the multimeter needle; a needle that fails to move indicates a blown thermal fuse.
How do you reset the code on a Maytag top load washer?
How do I clear the error code on my Maytag washer? To clear the error code on your washing machine, you have to press the pause/ cancel button twice and the power button once. If still, code is displayed, unplug the machine for a minute.
How do I clean the filter on my Maytag washer?
The quickest way to clean out your filter is to remove it from the unit and soak it in hot water, loosening any clog or trapped residue. If the filter cannot be removed, clean it out with brush. Some filters are disposable, so instead of cleaning them you can just throw them away and put a new one in place.
What is F5 on Maytag washer?
Did you receive a F5 E2 lid lock alert? The F5 E2 alert indicates the washer can’t engage the lid lock because there may be an obstruction in the lid lock area. Please check the lid lock area and remove any objects in that area.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
