Table of Contents
Your ecobee may keep on rebooting because of compatibility issues. Your ecobee may also constantly reboot if it has a circuit or a wiring issue. When compatibility issues are present, or wiring discrepancies exist, there is a good chance the system will not communicate with your new ecobee smart thermostat.
Why does ecobee keep calibrating?
The “Calibrating” message on your Ecobee thermostat screen indicates that it is measuring the current indoor temperature. Ecobee calibrates once it’s installed initially or when it reboots, and it typically takes around 5 to 20 minutes.
Why does my ecobee keep going offline?
Ecobee Thermostats fail to switch to the new channels after optimization, which causes the device to disconnect from the network. Ecobee has released a new firmware version 4.2. 0.171 for their Ecobee 4 Thermostats to resolve this issue. If you have an Ecobee 4, please verify that you have received the latest update.
What to do if ecobee turns off?
Open the panel on your furnace to expose the control panel where your thermostat wires are connected. Most systems have a purple 3 or an orange 5 amp fuse on the board—check this fuse to ensure that it’s intact. A blown fuse will have to be replaced. Once a blown fuse is replaced, the ecobee should power back on.
Why does my smart thermostat keep turning off?
If you’re using battery-operated thermostats, then the most common reason thermostats start turning off and on by itself is “Weak batteries”. Insufficient charge in the battery causes your thermostat to keep turning off and on frequently.
Why does my ecobee keep running?
This is a common problem with Ecobee and other smart thermostat systems. If this setting isn’t switched to “auto,” your fan could be stuck running all the time. With the fan in “auto” your system is going to automatically run the fan whenever it needs to adjust the temperature of your home.
How do I stop my ecobee from calibrating?
If your Ecobee is calibrating for an unusual amount of time, try power cycling it by removing the thermostat from the wall and then putting it back. Then, wait 20 minutes to see if it stops calibrating.
Does ecobee thermostat have a battery?
1 Battery Replacement Your ecobee room sensor is powered by a single 3 Volt CR-2032 battery.
Why is my ecobee app not working?
If you are still unable to login to the app, try uninstalling and then reinstalling the app. If you are on an older version, deleting and reinstalling the app will always replace your existing app with the most up to date version.
How do I reset my ecobee?
1 Factory Reset From the Home screen, press Menu. Select Settings. Go to Reset. Choose Reset All Settings then confirm your selection by pressing Yes. Choose the reset option that suits your needs: The ecobee thermostat will be reset to factory defaults.
How long does an ecobee thermostat last?
Ecobee states a battery life of 5 years (you can replace it yourself, when the time comes) and claims it’s smart enough to not be triggered by pets.
Does ecobee reset after power outage?
The Ecobee3 lite will turn back on when the power comes back on. There is no manual switch on the device, so it would be impossible to physically turn it on or off. Sorry, there was a problem.
Why does my thermostat Keep clicking on and off?
The click you hear from your thermostat is probably the electrical relay triggering the power to the furnace, air conditioner or heat pump. It is a normal sound. The thermostat typically clicks once when it triggers the start of a heating or cooling cycle and once when it signals the end of a cycle.
Why is my ecobee not turning off?
There are a few reasons why the Ecobee may not be turning off your HVAC system’s fan: The fan is set to “On” instead of “Auto.” The minimum fan runtime or heat dissipation time needs to be adjusted. The Smart Recovery setting is activated.
How many minutes per hour should I run my HVAC fan?
Most systems should run about 2-3 cycles per hour. How long should the furnace or AC run in a given cycle? Typically 10-15 minutes in mild weather. The closer you get to the max design temperature in heating (0 Degrees) or cooling (90 Degrees) the longer the run cycle will be.
How long is ecobee warranty?
3-Year Limited Warranty ecobee warrants that for a period of three (3) years from the date of purchase by the consumer (“Customer”), the ecobee thermostat (the “Product”) shall be free of defects in materials and workmanship under normal use and service.
Is ecobee thermostat accurate?
The Ecobee thermostat comes with various technological offerings to give you the most accurate temperature readout in your home. However, with the compatibility to connect with up to 32 different sensors, the Ecobee thermostat can inevitably run into some issues regarding accurate temperature readings.
How do you know if your furnace is overheating?
Signs of Furnace Overheating The Odor. This is the most common and obvious sign of furnace overheating. Frequent On-Off. Another giveaway of furnace overheating is that the furnace may turn on and off again and again. Noisy Furnace. Restricted Airflow. Short Cycling. End of Lifecycle. Dirt Deposits.
What does calibrate mean on a thermostat?
Proper calibration ensures that this sensor correctly reads your home’s temperature. The process involves matching adjusting the control element’s reading to the room’s temperature. You can check your thermostat’s calibration with a room thermometer. Place the thermometer a few inches away from your thermostat.
How long do batteries last in ecobee sensors?
CR2032 are the little silver coin shaped batteries used in the old ecobee Room sensors. The sensor will run for at least 18 months. The CR2477 used in the new Smart Sensors should last for five years.
