Table of Contents
In your lighting system, the ballast regulates the current flowing to the fluorescent lights and provides the voltage needed to start the lamps. The ballast takes in electricity and then regulates current throughout the bulbs. This is why a degrading ballast will cause the fluorescent lights to flicker.
How do I stop my fluorescent lights from flickering?
Brush dust out of sockets, then reseat firmly. If the tube still blinks when the light is turned on, wiggle it a few times while the light is on to see if this cures the problem. If not, take the tube out and inspect sockets closely to see if spring contacts are bent or corroded.
How do you know when a fluorescent bulb is bad?
Look for dark areas at the base of the bulb. When bulbs age and have been used for a long time, brown spots will appear. If darkness begins to form at the ends of the tube, the bulb may be near its end. While they may still light, they are wearing out and will die soon.
Can a bad ballast cause flickering?
Dimming or flickering If your bulbs are very slow to reach full brightness or strobe periodically, there may be a problem beyond the bulb. Water-damaged or faulty ballasts often struggle to regulate current.
Why does the tube light blink?
When the light switch is flipped on, the starter sends out a shot of electricity to the gas inside the fluorescent tube. That gas is then ionized and can conduct the electricity necessary to run the bulb. But there’s a slight delay in this process, so the bulbs flicker a bit before they turn on completely.
How long do fluorescent bulbs last?
Typical lamp life for a fluorescent bulb is about 20,000 hours, but this can degrade as a consequence of frequent switching (turning on and off). Burning life is extended if lamps remain on continuously for long periods of time.
How much does it cost to replace a ballast in a fluorescent light?
A replacement ballast costs about $10-25 depending on capacity and brand. The bite is that an electrician trip charge (which includes 30 or 60 minutes work) is going to be $75-150 probably – for about 5 minutes work on each light fixture.
How can you tell if a light ballast is bad?
Signs That Your Ballast is Bad Dimming or Flickering Headlights. If your HID bulb cannot produce its full brightness or strobe periodically, this is most probably a ballast problem. Strange Sounds. Headlights Not Working. Changing Light Colors. Constantly Blowing Fuse. Damaged Casing. Burn Marks. Water or Oil Damage.
Why does my fluorescent light flicker when off?
When a CFL flickers, the cause is usually in the light switch, which is either a dimmer or a switch with an illuminate rocker. Illuminated switches pass a small amount of current even when they’re turned to the “off” position, which is enough to charge the capacitor in the CFL and cause a momentary illumination.
Where is the ballast on a fluorescent light?
Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
How long do ballasts last?
According to the Certified Ballast Manufacturers Association, the average magnetic ballast lasts about 75,000 hours, or 12 to 15 years with normal use. The optimum economic life of a fluorescent lighting system with magnetic ballasts is usually about 15 years.
Why do fluorescent lights not turn on sometimes?
If you find your fluorescent light won’t turn on sometimes, there could be a variety of reasons why. It could be as simple as needing to replace the bulb or plug the light itself in; or, it could be something more serious, such as a blown fuse or a damaged/dying starter.
Do both fluorescent bulbs need to be replaced?
What about pairs of fluorescent tubes? In many fluorescent fixtures, power is sent through a pair of bulbs. If either bulb is bad, they may both flicker or one may flicker and the other show no life. My philosophy of sensible repair is to always replace both bulbs.
How do you make fluorescent lights last longer?
“Turning off fluorescent lights for more than five seconds will save more energy than will be consumed in turning them back on again,” the DOE explains. However, the lifetime of your bulb is affected by the number of times you turn it on and off.
Do fluorescent lights get old?
The Shelf Life of CFL (Compact Fluorescent Lamp) Light Bulbs CFLs typically have a rated service lifespan of 6000–15,000 hours, whereas standard incandescent lamps have a service lifespan, of 750 or 1000 hours.
Do I need an electrician to replace a ballast?
Yes. In fact, you really need a locking device to replace the ballast. – An electrician replaces the ballast on a fluorescent lamp. He uses a switch on the wall to turn off the fluorescent light.
Can a fluorescent light work without a ballast?
Reverted question “ Can I make a fluorescent light work without a ballast?” yes, you can, but you need something to reduce the current as the bulb warms up. So, you can drive a fluorescent with a pulse width adjustable power supply, but this is what is in an ‘electronic’ ballast.
Can you replace a ballast yourself?
The ballast takes in electricity and then regulates current to the bulbs. You can get a new ballast at a hardware store or home center and install it in about 10 minutes. However, buying a ballast can be expensive, so consider pricing a brand-new fixture for comparison.
