Table of Contents
Heat buildup, screwing bulbs too tightly, or placing LEDs in improper electrical circuits and accessories are common causes of LEDs stopping working. In addition, poor quality capacitors, drivers and diodes are also leading factors in reducing the life of LED bulbs.
Why are my LED lights not turning on?
Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. If your RGB strip lights won’t change colors try flipping your strip light around and reconnecting it.
What do you do if your LED lights don’t work?
LED strip does not light up at all 1) Confirm that your power supply’s voltage and current rating are compatible with your LED strip. 2) Confirm that your power supply is working correctly. 3) Check and isolate other accessories on the same circuit. 4) Check for any visible loose connections.
How do you reset your LED lights?
Insert a paper clip, or a similar sized object, into the reset hole on the controller (depicted below). Using the paper clip, press and hold the reset button inside the reset hole for eight (8) seconds. If done successfully, the light strip will flash five times then cycle through the colors blue, green and red.
Why are my LED lights not turning off?
Many of these electronic dimmers from the age of old incandescent and halogen lamps don’t meet the specifications for LED lights. If the load falls below the minimum load, the dimmer cannot switch off its output voltage completely even in the off position. As a result the LED continues to glow weakly.
How do I get my LED lights to work again?
First of all, please disconnect your power source for safety. Then, you need to unplug the dimming cord from both the power supply and the LED strip light. Next, plug the power supply and LED strip back into the receiver unit and reconnect the power supply to power.
Do LED lights burn out?
Unlike incandescent light bulbs, LEDs don’t produce light using heat. This is part of what makes them so energy efficient. The downside is that their components can be sensitive to overheating, which can cause them to burn out prematurely.
How long do LED Strip Lights last?
LEDs have an unbelievably long expected life-span, compared to both incandescent and fluorescent lights. With an average life-expectancy of some 50,000 hours, LED strip lights will still be burning bright in 17 years’ time, long after their traditional counterparts will have expired.
How long do LED lights last?
One of the biggest advantages of LED light fixtures, is their extended lifespan. While incandescent light bulbs were built to last around 1,000 hours, the most enduring LED light fixtures have been tested to last as long as 100,000 hours. On average LED light bulbs will not have to be changed for at least 20 years.
How do I reset my LED WIFI strip?
press and hold the power button of wifi led controller for 5-6 seconds , then you can reset the light strip controller again.
Does any remote work for LED lights?
Yes, One remote can control multiple receivers, you need to match code with each receiver firstly,following the steps: . Correct connection led strip light, make work normal. Correct connection led strip light, make work normal.
Why are my LED lights only blue?
Your light probably has a long wire connecting it to the power source. If that wire is running parallel to a wire which has power, perhaps they are coiled together, then there is a possibility of capacitive coupling into the wire that leads to your LED.
Why did my LED remote stop working?
If your remote control suddenly stops working or your lights start blinking, you may need to reset the controller and pair it back to the receiver unit. The controller sometimes un-pairs itself from the receiver due to a loose connection, radio interference from an external source or a low battery in your remote.
Why do my LED lights only work when I touch them?
Some LED can illuminate with such a low current. When your body touches another power source (let say leakage current from your nearby AC appliance), your body resistance is ‘low’ enough to conduct electricity from that appliance to illuminate the LED.
How do you fix lights that won’t turn on?
Tighten the bulb if it is loose, then try the switch again. If a problem remains, be sure the switch is off, remove the bulb and substitute a new one. If the light does not work with a new bulb, check whether the circuit breaker or fuse governing the fixture has tripped or blown.
Why are my LED strip lights not bright?
LED bulbs can lose their brightness due to premature aging, bad internal components like a capacitor or LED arrays, or the common cause of loose wiring. Heavy load appliances on the circuit can also cause that LED lights are dim.
How do you fix dim LED strip lights?
Minimizing voltage drop and dimming First, minimize wire length wherever possible. This might mean running wire through a wall, or a ceiling, instead of going around a room – if possible. Second, make sure to use an adequately sized wire when making runs between your power source and light strip.
