Table of Contents
If half your LEDs are not working, it means that there are 2 strings of LEDs wired together in parallel – each parallel string has LEDs in series. You likely have a broken wire, or an LED bulb is broken or out of the socket.
What do you do when half your LED lights don’t work?
If the complete section between cutpoints is not working, this is a very similar problem to a damaged LED or resistor – most likely caused by a dry solder joint. Solution: In most cases here the only option is to replace that section of the strip. You can do this by swapping the full strip.
Why is a part of my LED light not working?
Bad Pin Connection – If your LED strip light fails to turn on at all, then check your pin connections. Most likely, the pin is not inserted correctly. In rare cases, the pin is faulty. If your RGB strip lights won’t change colors try flipping your strip light around and reconnecting it.
Why is one part of my LED lights a different color?
LEDs, especially cheap LEDs (including most bulbs), tend to be very inconsistent in color. This is because the manufacturer does not tightly control binning, or separating LED batches by slight variations in color. Sacrificing binning cuts cost, but also consistency in light color.
Can you cut LED Strip Lights?
You can, but we wouldn’t recommend it. By cutting an LED strip light anywhere other than the designated cutting point, you run the risk of damaging the components on the strip itself, as well as the circuit board. This may ultimately result in the strip light not working.
How long do LED Strip Lights last?
LEDs have an unbelievably long expected life-span, compared to both incandescent and fluorescent lights. With an average life-expectancy of some 50,000 hours, LED strip lights will still be burning bright in 17 years’ time, long after their traditional counterparts will have expired.
What if I cut my LED lights?
Will they continue to work if they are trimmed down? Yes, LED strip lights will carry on working after they’ve been cut as long as you cut along the designated lines. LED strips are made up of several individual circuits, so each cut line demarcates the end of one circuit and the start of a new one.
Can LED lights be fixed?
YES. Unlike traditional incandescent bulbs, modern LED bulbs allow for almost everything to be repaired. What you need to do is to find out the problem and take reasonable action to repair, or replace some damaged parts of the LED bulb, your lamp can work properly again.
What can go wrong with LED lights?
Most Common Problems with LED Lights Using the wrong current. LED bulbs overheat. Low quality solder and wire bonds. Improper use of LED lighting. Issues with color rendering. Existing fittings and fixtures are incomparable. Light Emitting Efficacy. Overly complicated circuits.
Can you reconnect cut LED strips?
A: If the LED light strip you purchased can be cut, the remaining part that you have cut off cannot be used anymore. If you want to reconnect them after cutting, you must use an additional 4 pin connector to reconnect.
How do I reset my LED lights?
Insert a paper clip, or a similar sized object, into the reset hole on the controller (depicted below). Using the paper clip, press and hold the reset button inside the reset hole for eight (8) seconds. If done successfully, the light strip will flash five times then cycle through the colors blue, green and red.
What are the LED lights on TikTok?
The TikTok lights are LED strip lights that come in a wheel that you can unravel. From there you can take them and stick them on anything: your ceiling, walls, bed, closet, even outdoors. Then, using a remote, you can change the color, the speed, or even a cool fade with multiple shades.
Can LED lights catch on fire?
Because of this, LEDs produce far less heat than other light bulbs, and heat is how fires start. Therefore, though an LED might feel warm to the touch, it is extremely unlikely that an LED would start a fire.
What brand are the TikTok LED lights?
The most popular ones on TikTok are none other than the RGB and dreamcolor LED strip lights. You can adjust them to different colors however you want based on personal preferences. The dreamcolor LED strip light can also make a strip light display multiple color effects at the same time.
Can you leave LED lights on 24 7?
To put it simply, well-manufactured LED lights are extremely long-lasting and can be left on 24 hours, 7 days a week. This is because, unlike conventional types of light, LEDs produce minimal amounts of heat, which means they are unlikely to overheat or set on fire. In some scenarios, LEDs can and will fail.
Does LED lights get hot?
Yes, new technology LED lighting can and will get hot, but when compared to the lighting of the past, temperatures are much safer. The heat from the lighting will also warm your surrounding environment but in comparison to old incandescent lighting, this ambient heat is greatly reduced when using LED lighting.
