Table of Contents
Which way does crown molding go?
Crown moulding is installed in the reverse fashion of base moulding. The deeper grooves go on the bottom, and shallower grooves belong on the top. Generally, crown moulding extends further down the wall than on the ceiling. The concave (cove) side goes down, and the convex (rounded) side goes up.
What angle do you cut crown molding for cabinets?
Cut the Molding with the Miter Saw Adjust the miter saw to cut at the correct 45-degree angle taking into account when cutting that, since the molding is being held upside down, that the “bottom” of the molding is actually the top.
Is crown molding on cabinets outdated?
To answer your burning question: No – crown molding will never go out of style. Keep the above tips in mind when considering purchasing crown molding for your home.
Can crown molding be upside down?
Crown molding can be installed upside down, although it is usually not recommended. If you like the unconventional style and keep it consistent throughout your home, there is a chance that your guests may not even notice your alternative design.
How do you fill the gap between cabinets and ceilings?
You can build the cabinets to the ceiling (most expensive option), keep the area open (no cost!), build a soffit to match the cabinets, or add a drywall soffit.
What is the trim on top of cabinets called?
Crown molding is decorative trim that is added to the top of your cabinets. The benefit of installing crown molding is that it draws the eye upward, showcasing the elegance of your cabinets. Crown molding can either bond with the ceiling or allow for space above the cabinet.
When should you not use crown molding?
There are a couple of situations when you don’t want to use crown molding. If you have cathedral or vaulted ceilings, a typical crown molding will probably not fit or look good. Also, crown moldings need a distinct starting and stopping point, ideally going around a room in both directions and meeting again.
Is Crown Moulding still in style?
While crown molding is still a popular look, avoid it in these types of rooms as it may make the space look too busy.
Does crown molding add value?
Crown Molding can lead to increased home value and a positive ROI depending on how much you have invested in the project. Many homeowners want easy projects that will increase their resale price, and you can do that by adding crown molding.
Which end is top of crown molding?
Crown molding can look good both ways: in its usual alignment or upside-down, which makes it difficult to determine the end that’s supposed to be the top. Generally, the end with the least amount of detail goes on top, and the decorative trim faces the bottom.
How far down the wall does crown molding go?
For standard 8-foot-high ceilings, the crown/cornice height should be 2½ to 6 inches; for 9-foot ceilings, 3 to 7½ inches, and for 10-foot ceilings, 3½ to 8 inches.
Should crown molding touch the ceiling?
Crown molding does not always have to be installed against both the wall and the ceiling. For a fun effect, consider installing the crown only against the wall and moving it downward about a few inches.
How can I hide the gap between my ceiling and crown molding?
You can minimize the appearance of the gap by simply squeezing in some silicone caulk between the molding and the ceiling. Unfortunately, it may leave some excess caulk once you apply it. However, you can remedy this by taking a damp cloth and wiping away the excess (use mineral spirits with silicone caulk).
Is crown molding necessary on kitchen cabinets?
Crown molding is an iconic look for traditional cabinets. Without it, wall cabinets are typically left incomplete and need the finished look. This applies to kitchens that can afford to have the molding installed.
Is crown molding used in kitchens?
Traditional crown molding tends to be the industry standard for kitchen cabinetry. Here it has been used to fill an empty space between the cabinets and the ceiling. If you have an average ceiling height, about 8 feet high, 3 to 6 inches of crown molding can usually help fill any kitchen cabinet gaps.
How do you find the angle of a corner cabinet?
Measuring Around Corner Cabinets One corner of each board must contact the joint between cabinets. Make a mark where the two boards intersect, then draw a line from that mark to the corner that contacted the cabinet joint. This line is the bisection angle you’ll need to cut crown molding accurately.
How do you find the spring angle of crown molding?
The crown spring angle is the angle measured from the back of your crown molding to the wall when holding the bottom of your crown molding firm against the wall (in full contact with the wall).
Do you glue or nail crown molding?
Crown is typically nailed up with a 2” finishing nail and a compressor and finishing gun. Outside corners are usually done with a brad nailer and 1” brad nails with glue. Studs are generally 3-1/2”, drywall a ½” and the crown moulding a minimum of ½”; therefore 2” finishing nails are necessary.
Do you have to use a nail gun for crown molding?
We’re talking crown molding at the top of the wall, baseboards at the foot, or both. Installing it is as simple as buying a box of itty-bitty finishing nails and hammering in the molding. Seriously, you do not even need a nail gun.
Do modern homes use crown molding?
Modern Interiors do not use crown, Traditional has additional layers of decorative molding, Transitional is somewhere in the middle.
Does crown molding make a room look smaller?
Crown molding adds an elegant touch to a room. However, depending on how you paint them, they can actually make a room appear smaller. But if you paint the molding the same or a similar color to the wall, even darker rooms will appear more spacious.
Where should you not put crown molding?
It’s untrue that crown molding should not be installed in rooms with low ceilings. In fact, using moldings that project further than the wall can provide an optical illusion that makes ceilings appear taller than they actually are.
