Table of Contents
Slide the new filter in with the arrow pointing toward the furnace. Replacing your air filter is not difficult. Remember that air flows from your ducts, through the filter, and into the furnace. The arrow on the filter should always point toward the furnace.
What happens if furnace filter is backwards?
When a furnace filter is placed backwards, the fibers can’t do their job properly. This means your furnace has to work harder to generate the same air flow, resulting in increased energy costs. Particles are also allowed to build up irregularly, making the furnace working even harder to draw air.
Is it OK to run the furnace without a filter?
Technically, you can temporarily run a furnace without a filter. However, it’s important to emphasize the word “temporarily” here. Poor air quality: For one, not having a filter in place means there is nothing to prevent dust and debris from being sucked into your furnace and recirculated throughout your home.
Does the arrow point up or down on an air filter?
Air filters have arrows printed on the sides of them that show you which way they are supposed to be installed. These arrows should be pointing in the direction that air flows through your system, which is away from the supply ducts and (typically) toward the blower.
Should air filter arrow point up or down?
Make the arrows face the ceiling or wall. If your filter is on the ceiling, the arrow should face the ceiling. If your filter is on the wall, the arrow should face the wall. All of QualityAirFilters filters come equipped with the arrow for easy installation.
Why is the furnace blowing cold air?
A clogged filter is one of the leading reasons for a heater blowing cold air. But even if you swap the air filter with a brand new one, dirt and debris can still be found within the unit. This could eventually lead to overheating. If your furnace looks pretty dirty, call an HVAC provider for a professional clean.
How often should you change air filters in a furnace?
In general, this is how often changing furnace filters needs to be done: For 1- to 2-inch filters, replace them every 1 to 3 months. For 3- to 4-inch filters, replace them every 6 to 9 months. For 5- to 6-inch filters, replace them every 9 to 12 months.
Why does my furnace only runs for a few minutes?
Low airflow When the exchanger heats up to the maximum temperature, the furnace shuts off after a few minutes. The furnace won’t be able to pull fresh air into the blower if the air filters are clogged with dust, pet hair, and other debris. You should also make sure to open all of your air supply vents.
What happens if you install air filter backwards?
By installing your filter backwards, air will have a harder time flowing through the filter and your air handler will have to work harder to make up for the loss of airflow. This could lead to higher utility bills and possibly damage your furnace or air conditioner.
Why is my furnace running but no heat?
Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.
How do you reset a furnace after overheating?
How to Reset Your Furnace Turn down the thermostat to its lowest setting. At the circuit breaker, turn off the power to the furnace. If this is a gas furnace, turn off the gas supply at the valve for the main gas pipe, but leave the pilot’s gas supply on. If the pilot light was out, light a match to relight it.
Why does my furnace keep running?
A dirty furnace filter is the number one reason we’ve found that furnaces run constantly. The air filter captures dust, pet hair, and debris that could damage the furnace and keeps it from getting to the heat exchanger. If the filter is dirty, it restricts airflow across the heat exchanger, which causes it to overheat!Nov 24, 2015.
Why does my furnace filter get dirty so fast?
Leaky Duct Work According to ENERGY STAR, a typical house loses 20-30% of air through leaks in the duct work and poor duct connections. Leaving these untreated can not only kill your furnace filter quickly, but also result in higher energy bills.
Why does my furnace filter get dirty so quickly?
When the thermostat’s fan setting is set to “ON” the indoor blower will run 24/7, constantly circulating air over the air filter. So now the filter is constantly catching airborne contaminants, causing it to quickly get dirty. Furthermore, your energy bills are higher because running a blower nonstop ain’t cheap.
How often should you clean furnace ducts?
Experts advise having your air ducts cleaned every 2 to 3 years to prevent many maintenance and health problems before they start. However, homes with pets or children with allergies should have their air ducts professionally cleaned more frequently than the recommended average.
How often should furnace cycle in winter?
How Often should Furnace Cycle in Winter? Answer: Winter is the time while a furnace has to work the most. So, the average single-stage furnace should cycle 6-8 times in an hour. The cooler the temperature is, the more this cycling frequency will be.
Why does my furnace keep starting and stopping?
The most common issues that can cause your furnace to stop and start again are: Restricted Airflow: Your furnace draws in air from your home and then cycles the warm air back into your home. If your intake vents and exhaust vents are blocked or airflow is restricted, then you could experience short cycling.
