QA

Which Of The Following Is True About Installing The Motherboard And Connecting Power

Which of the following represents the correct order in which you should install components into the case after disassembling a computer?

in what order should you install components into the case after disassembling a computer? power supply, drives, motherboard, cards.

What is the power connector on a motherboard?

The ATX 24-pin power supply connector is the standard motherboard power connector in computers today. The connector itself is a Molex 39-01-2240 connector, often called a Molex Mini-fit Jr.

What do you call a connector on a motherboard that connects 2 pins that stick up from the board?

What do you call a connector on a motherboard that consists of pins that stick up from the board? S. Header. Which of the following can be described as round plastic or metal pegs that separate the motherboard from the bottom of the case? Stand-off.

At what point during the motherboard installation should you install the motherboard drivers?

When everything is working fine, you have to install the motherboard drivers. The installation of the motherboard driver should only be done after the system boots without errors.

When installing a processor you must line up the red circle?

When installing a processor, you must line up the red circle on the processor with the right-angle mark on the motherboard. After installing the processor, if the system begins the boot process and suddenly turns off before completing the boot, the processor is most likely overheating.

What component is most likely to be installed in a PC?

30 Cards in this Set A tower case conserves space since it can double as a monitor stand. t or f false What is most likely to be installed in a PC, is considered primary storage, and has Windows 7 installed on it? hard disk drive.

Where does power SW connect to motherboard?

Among the loose cables in your case, you’ll find a two-pin connector, which is usually marked PWR SW, but check the case’s manual if you’re unsure. The power switch wires need to connect to the power jumpers on the motherboard. Typically, these pins are located on the bottom-right section and are usually unmarked.

Why might a motherboard be installed on top of spacers quizlet?

The motherboard sits on elevated screw holes or spacers to keep it from touching the case. When disassembling a computer, it’s okay to stack circuit boards on top of each other as long as you follow ESD protection rules.

Why are motherboards installed in the case using spacers?

Motherboards are installed in the case using spacers, because if the fine traces or lines on the bottom of the board were to touch the case, a short would result when the system is running.

Why is motherboard called motherboard?

Because it’s the Main Circuit Board in a Computer One of the most compelling reasons why the motherboard is named so is because it is the main circuit board in a computer. Hence, the name motherboard sounds quite fitting here.

When installing hardware to a motherboard when do you install the drivers when do you install the drivers for Usbs?

soon as you are in windows, you’ll have your user account, configure the start menu and security settings how you want it, then pop in your motherboard disc to install the drivers. Video driver disc next, and you should have everything good to go.

Which motherboard slot should you install a new high end graphics card in group of answer choices?

It is best to slot it into the 16x PCIE slot, on a modern day motherboard, this is generally the first or second pcie slot from the CPU socket. You could place the GPU on other slots as well but not all the pcie slots are at 16x unless you have a really special one (which usually costs an arm and a leg).

Which motherboard slot should you install a new high end graphics card?

As a rule of thumb, you should put the graphics card in the first PCIe x16 slot of your motherboard. The first PCIe x16 slot has 16 PCIe lanes and thus can offer the highest throughput compared to the rest of the PCIe slots found on your PC.

When installing a processor you must line up the red circle on the processor with the right-angle mark on the motherboard true?

When installing a processor, you must line up the red circle on the processor with the right-angle mark on the motherboard. After installing the processor, if the system begins the boot process and suddenly turns off before completing the boot, the processor is most likely overheating.

Which socket type is soldered to the motherboard along with the CPU?

1. BGA Sockets. BGA means “Ball Grid Array.” When your motherboard is soldered to a BGA socket, that means the socket is permanently attached to the motherboard during production was done. Ball grid array (BGA) sockets are welded in the motherboard of notepads and PCs, where CPU chips don’t have pins.

What type of bus does PCI use?

Whereas PCI uses a 32-bit or 64-bit parallel bus, PCI Express uses a serial bus, which is faster than a parallel bus because it transmits data in packets similar to how an Ethernet network, USB, and FireWire transmit data. A PCIe expansion slot can provide one or more of these serial lanes.

What component is most likely to be installed in a PC is considered permanent storage and typically stores the operating system as well as its applications?

External hard drives are mainly used for storage Every computer – whether it’s a tower desktop or laptop – is equipped with an internal hard drive. The hard drive is where all your permanent computer data is stored. Whenever you save a file, photo, or software to your computer, it’s stored in your hard drive.

Which is the most common form factor used today for computer cases power supplies and motherboards?

The most common form factor is ATX, which evolved to mini-ATX, nano-ATX, pico-ATX, and further. A different type of form factor, and smaller than the ATX is the ITX, which is significantly smaller than the micro-ATX.