Table of Contents
Which of the following devices can be used to distribute electrical power along with network data on twisted pair Ethernet cabling Cat 5 or higher )? Quizlet?
Power over ethernet (POE) technology can be used to distribute electrical power along with network data on twisted-pair Ethernet cabling (CAT 5 or higher). Power is usually supplied by a PoE-enables Ethernet switch.
What is the maximum cable length on a segment of a 1000baset network?
1000BASE-T (also known as IEEE 802.3ab) is a standard for Gigabit Ethernet over copper wiring. Each 1000BASE-T network segment is recommended to be a maximum length of 100 meters (330 feet), and must use Category 5 cable or better (including Cat 5e and Cat 6).
What is the maximum cable length on a segment of a 1000baset network quizlet?
A Physical layer standard for networks that specifies 1-Gbps transmission over fiber-optic cable using baseband transmission. 1000Base-SX runs on multimode fiber. Its maximum segment length is 550 meters.
Which type of fiber optic cable supports 10 Gigabit Ethernet with a maximum segment length of up to 40km?
This 10GBase-ER SFP+ delivers 10 Gigabit connectivity over single-mode fiber cable with a range of up to 40 km (24.8 mi.).
Which of the following is a wired networking method most commonly used by desktop computers in other network devices to connect to a local area network?
Which of the following is a wired networking method most commonly used today by desktop PCs and other network devices to connect to a local area network? Answer: Ethernet is a wired, local area network (LAN) standard.
Which of the following is considered an input device?
Which of the following is considered an input devices? A touchscreen is considered an input device. A touchscreen is a monitor that can receive input through touch. A hard disk is a magnetic storage device used to store computer data.
Which of the following cables are used in 1000BASE-T?
1000BASE-T uses four pairs of Cat5 UTP cable for a maximum length of 100 m. 1000BASE-TX uses two pairs of shielded twisted pair (STP) using Cat6 or Cat7 cable for a maximum length of 100 m. It uses more expensive cables but less expensive electronics; it is no longer widely used.
What is the maximum cable length for a 100basetx network?
100BASE-TX is the predominant form of Fast Ethernet, and runs over two wire-pairs inside a category 5 or above cable. Each network segment can have a maximum cabling distance of 100 metres (328 ft).
Which of the following is the maximum cable segment length allowed?
Standards for cable distance recommend that Cat5, 5e, and 6 cables have a maximum cable segment run length of 100m or 328 feet. Four pairs of twisted wires are used to construct Category 5, 5e, 6, and 6a cable, which is most commonly unshielded, as in UTP.
Which type of fiber-optic cable supports longer run lengths?
Singlemode fiber is typically used in network connections over long lengths and is available in a core diameter of 9 microns (8.3 microns to be exact).
What is the maximum cable length for an Ethernet UTP cable quizlet?
100 meters or 328 feet. What is the maximum cable length for UTP? 100 meters or 328 feet.
What is the maximum cable length for twisted pair used for Ethernet communication?
Ethernet – 100 meters (328 feet) There are a few different versions of ethernet cable, but they all have a maximum distance of 100 meters (328 feet). It should be noted that Cat7 cable has harsher distance limits than Cat5e, Cat6, and Cat6a.
Which connection type can support Gigabit Ethernet?
The type of twisted pair cable that supports Gigabit Ethernet is a Cat-5e cable, where all four pairs of twisted wires in the cable are used to achieve the high data rates. Cat-5e or higher cable categories are recommended for network video systems.
Which of the following is a 10 gigabit per second Ethernet fiber-optic standard?
10 Gigabit Ethernet (10GE, 10GbE, or 10 GigE) is a group of computer networking technologies for transmitting Ethernet frames at a rate of 10 gigabits per second. It was first defined by the IEEE 802.3ae-2002 standard.
Which of the following connectors is used with Ethernet 100BaseT networks?
RJ45 connectors are used with Ethernet 100BaseT networks.
What is connecting devices in networking?
Devices can install a Local Area Network (LAN) are the general type of network devices used by the public. A LAN needed a hub, router, cabling or radio innovation, connection cards, and a high-speed modem if an online connection is necessary.
What is router computer?
A router is a networking device that forwards data packets between computer networks. Routers perform the traffic directing functions on the Internet. A router is connected to two or more data lines from different IP networks.
Which of the following is a wired network?
Examples include telephone networks, cable television or internet access, and fiber-optic communication. Most wired networks use Ethernet cables to transfer data between connected PCs. Also waveguide (electromagnetism), used for high-power applications, is considered wired line.
What are the 10 input devices?
10 Examples of Input Devices Keyboard. Mouse. Touchpad. Scanner. Digital Camera. Microphone. Joystick. Graphic Tablet.
What are the examples of output devices?
Output devices Monitor – The main output device of a computer. Printer – Used to print information on paper. Speaker – Converts digital signals into audible sound waves. Projector – A device that is used to project video output from the computer onto a wall or screen.
Which of the following are output devices?
Detailed Solution. The correct answer is Speaker. An output device is any hardware device used to send data from a computer to another device or user. monitors and projectors (video), headphones and speakers (audio), or printers and plotters (physical reproduction in the form of text or graphics).
What does the T in 1000BASE-T stand for?
Techopedia Explains 1000Base-T The 1,000 refers to the transmission speed of 1,000 Mbps, while “base” refers to baseband signaling, which means that only Ethernet signals are being carried on this medium. The “T” refers to the twisted pair cables this technology uses.
Which wire pairs are used on a 1000BASE-T network quizlet?
1000BaseT networks, also called Gigabit Ethernet networks, use all four wire pairs: green, orange, blue, brown.
What type of cable is required for a 100Base T network?
100Base-T uses two pairs of wires in at least Category 5 UTP cable, while 100Base-TX requires two pairs in Category 6.
