Table of Contents
The high side, or discharge line, will be the line connected to the compressor from the bottom or lower position. It will not be wrapped in insulation and will be warm to the touch. This is where freon exits the compressor as a liquid.
How do you tell a high side from low side AC?
The low side line of the system will have a larger diameter metal pipe than the high-side. The low side service port is usually located between the AC compressor and evaporator. The low side service port will have a black or blue plastic cap that needs to be removed.
Which is the high side and low side?
A semiconductor switch placed in the upper circuit with respect to an external load is referred to as high-side drive (power supply side), and when mounted in the lower circuit is called low side drive (ground side).
Where is the low side of the AC?
The low side service valve is located in the line that runs from the compressor through the evaporator (firewall) and up to the condensor on the low pressure (suction) side of the system.
What color is high side on AC?
Manufacturers color-code the hoses to distinguish between high pressure and low pressure. Low-side hoses are blue while the high side is red.
Can you charge AC on high side?
@engineercyprus You can both use it to check the high side pressures, both static and running, and to charge refrigerant, but you’ll be able to charge refrigerant through the high side service port only with the compressor off, after vacuuming the system (if you don’t vacuum, refrigerant won’t get pulled inside).
What is high side and low side in HVAC?
High side and low side refer to the pressures in the two halves of the system. AC works by compressing refrigerant in the compressor (the beginning of the ‘high side’), cooling in the condensor it, and then expanding it to absorb heat (where it enters the low side).
What is high side vs low side switch?
The low-side switch is switching ground while the high-side switch is connecting the voltage supply. Generally in a circuit, you want to keep the ground connected and switch the power.
When would you use a high side switch?
High-side switching is the preferred switching technique in situations where short circuits to ground are likelier to occur than short circuits to the positive power line. Think for instance of cars or machines where most of the structure or body is connected to ground.
What is a high side output?
A high side driver is one in which the switching element is between Vcc and the load. A low side driver is one in which the switching element is between the load and common. A self-contained load such as a DC motor, solenoid/relay, light or LED string, can usually be driven by either method.
What should the high and low side pressures be?
Actual readings will vary according to ambient temperature. The low-side should be near 30 PSI at 90 degrees Fahrenheit or less. Pressure that is too much lower or higher shows there is a problem. On a properly working system, high-side pressure will be about twice the ambient temperature, plus 50 PSI.
Which one is the low pressure AC port?
Both ports are located on the air conditioner’s metal pipes. The low-side port, like the name suggests, is lower on the pipes towards the front of the engine. While the low-side port is intended for recharging Freon, the high-side port is used for maintaining an air conditioner’s internal pressure.
Which AC line is cold?
The Copper Pipe (Suction Line) should be sweating and cold to the touch during a hot day. If it is not cold, your compressor could be off (bad capacitor/ hard start kit) or low on Refrigerant. Your Breaker is Tripped.
What color is high pressure?
High pressure is colored in blue. The choice of the color blue has nothing to do with temperature. High pressures can bring with warm or cold weather depending on the type of high pressure it is. Low Pressure System: This is a region of relatively lower pressure.
Will Freon leak without cap?
Schrader core valves that are inside these service ports can leak, even with a schrader valve cap. It’s not a guarantee you’ll see a leak for a couple of reasons. The refrigerant may have already leaked out.
What is the high side AC port for?
The high-side charge port is a quick-connect fitting that provides access to the high-pressure side of the A/C system. Most A/C systems are evacuated and filled from the high-side charge port in the assembly plant.
Does freon go in the high side or low side?
The freon is added on the LOW PRESSURE SIDE ONLY. The hose tool you bought is made so you can only hook to the low side as the high side and low side fittings are different sizes and shapes for SAFETY’S SAKE.
What is the high pressure AC port used for?
The high side service port is a fitting that provides access to the high pressure side of the AC system and the low side service port is a fitting that provides access to the low pressure side of the AC system.
What is meant by high side switch?
High-side load switches are highly integrated power switches used to connect and disconnect a power source from a load. Using a load switch instead of a regular MOSFET offers several features including simplified design, small footprint, and protection features.
What is high side and low side MOSFET?
“Low-side” means the current travels from the load or device through the mosfet to ground (common). “High-side” means the current travels from the supply through the mosfet to the load and then to ground.
