Table of Contents
Where should cabinet handles be placed?
Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.
Where do pulls go on drawers?
When it comes to cabinet pulls placement for drawers under 24”, pulls are most often centered and installed in the middle of the drawer panel. This creates a really clean + high touch finishing look for your cabinetry. Like with knobs, if the drawer is 24” or wider you can add a second pull.
Where do you put cup pulls on drawers?
Cup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing.
Should cabinet pulls be vertical or horizontal?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
Should kitchen handles be vertical or horizontal?
The universal rule is that handles are placed vertically on doors and horizontally on pull-out drawers. Stand in your new kitchen and hold your handles against the drawers and cabinet doors to try out different heights and positions for each of them.
Where do you put pulls on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
Should cabinet pulls be centered?
As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.
Where do pulls go on slab cabinet doors?
For slab doors, you will want the hole placement to be equidistant from the bottom and side of the cabinet. 2″ is typically a good distance. For pulls, you will want the end of the pull to be in this position. Adjust the screw hole placement accordingly if necessary.
How do you measure for cabinet pulls?
To accurately measure existing fixing centers, open your kitchen door or drawer and measure the distance between the center of each screw. This measurement should be used when specifying your new handles.
How Big Should Cup pull be?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width.
How do you install drawer pulls evenly?
Most drawer pulls are centered on the drawer fronts, but if the cabinet you’re working on has two or three drawers the same size and one larger one at the bottom, install the bottom knob (or pull) higher than the center of that drawer front. Install it so all the knobs on the cabinet are spaced evenly.
Do you put hardware on false drawers?
Having a false drawer handle adds continuity and are more visually appealing than having a bald-faced drawer. Although having a drawer handle on a false drawer does not increase storage space, many enjoy the look of having all of their drawer faces with knobs or handles.
How long should bar pulls?
Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.
What size pulls for 36 inch drawers?
Oversize Drawers (36″ or larger) For larger drawers, consider investing in longer-length stainless steel pulls such as 6”, 8”, 10” or even 12”. Another alternative to this is by using double smaller pulls, such as two 3” or two 5” pulls.
Can you mix pulls and knobs on cabinets?
Yes. You can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.
What are Shaker cabinets?
In the world of cabinetry, shaker cabinets are units that are simple but aesthetically pleasing. Shaker cabinet doors are cope-and-stick construction and recessed panel doors with simple and clean inside and outside edges. This cabinet style is known for its minimalistic look when placed in a kitchen or bathroom.
How do you decide between knobs and pulls?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Are knobs or pulls better for kitchen cabinets?
In many instances, knobs make it easier to open upper cabinets. Pulls, on the other hand, offer easier operation of lower cabinets. Just take a look at this Victorian kitchen. You’ll notice that all the upper cabinets have knobs, while the majority of the lower cabinets feature pulls.
