Table of Contents
The best way to measure your tread depth is to stick the probe into the shallowest groove on the tire, press the shoulders of the probe flat against the tread and then read the result. All gauges should measure both in the 1/32″ United States standard and in millimeters.
Where do you check tire tread depth?
Take a standard U.S. Penny and insert it into the tread, with Lincoln’s head facing down and out. If you can see all of Lincoln’s face, your tread depth is below 2/32 of an inch, and you need new tires. Check your tires in multiple locations to be safe.
What is typical new tire tread depth?
Tread is the rubber on the tire that touches the road. New tires have an average tread depth of 8 to 9 millimeters (10/32 to 11/32 inches).
Should I replace tires at 4 32?
The Tire Rack’s advice is that if rain and wet roads are a concern, you should consider replacing your tires when they reach approximately 4/32″ of remaining tread depth. Since water can’t be compressed, you need enough tread depth to allow the rain to escape through the tire’s grooves.
What is good tread depth for used tires?
Used tires tread can be up to 90%, but the average is 6-8/32”. Tires in good condition should have a minimum of 6/32” to be useful, or 4/32” if the tire is 13-14”. The average legal minimum tread depth is 2/32”, but driving becomes unsafe with such a tread.
Is 5mm tire tread good?
Insert the gauge into the tyre tread groove with the coloured scale touching the tyre. If the red is visible the tyre tread is below 1.6mm. This means the tyre is 100% worn and should be replaced urgently. If the green is visible, the tyre tread is above is 5mm and is safe to drive.
Is 5 32 A good tire tread depth?
Tread depth what to do 6/32” Your tire’s tread depth is sufficient for 3-seasons but nearing minimum for a winter tire. 5/32” If wet roads are a concern, consider replacing your tires. 4/32” – 3/32” Seriously consider replacing your tires as soon as possible. If it’s a winter tire, 4/32” is the minimum.
How often should tires be replaced?
When Should You Replace Your Vehicle’s Tires? As a general rule, the National Highway Traffic Safety Administration (NHTSA) recommends that drivers change the tires on their vehicles every six years.
How many miles are tires good for?
Your tires should last 50,000 to 60,000 miles on average. But that really depends on the manufacturer. Some manufacturers build their tires to last up to 80,000 miles, while some design their tires to last as little as 30,000 miles. You can see how many miles to expect out of a tire by checking its treadwear rating.
How often should your tires be rotated?
This common maintenance task—which should typically be done every 5,000 to 8,000 miles—isn’t one you should ignore. It may seem minor, but remember: Tires are the only thing that comes between your 2-ton vehicle and the road.
Why do new car tires wear out so fast?
The tires that came with your last new car were not designed by Michelin, Goodyear, Bridgestone or any other tire manufacturer. They were designed by the manufacturer of your car. This is because virtually all auto manufacturers specify very soft rubber which means they wear out too fast.
How many 32nds are on a new tire?
In the United States, tire tread depth is measured in 32nds of an inch. New tires typically come with 10/32” or 11/32” tread depths, and some truck, SUV and winter tires may have deeper tread depths than other models.
Is the penny test for tires accurate?
For years, motorists have been told the “penny test” is an accurate indicator of whether or not you need new tires. The test is conducted by sticking a penny head down in a tire tread; if you see all of Lincoln’s head, then you should change the tires. The one with an eighth of an inch of tread stopped in 300 feet.
What is the penny trick for tires?
The Penny Test Insert a penny with Lincoln’s head upside down into a tire tread groove. If Lincoln’s head is covered and no longer visible between the grooves, your tread depth is good. If you can see all of Lincoln’s face, it means that the tire tread is 2/32 inches deep or less and it’s time to replace them.
What is the minimum tire tread depth in Canada?
Tread Depth Requirements Canadian law requires a minimum 1.6 mm tread depth, but some provinces have even stricter requirements.
How do you measure tire tread with a Canadian quarter?
The quarter test A classic way to measure winter tire wear is to use a quarter. Insert a 25¢ Canadian coin in one of the grooves with the caribou facing down. If you see the tip of its nose, it means the tread depth no longer meets 6/32”, so the tire probably won’t last all winter or 10,000 km.
