QA

Question: Where To Drill Weep Hole In Sump Pump

Where do you drill the weep hole in a sump pump?

Your Weep Hole should be drilled between the discharge and check valve. The hole should be drilled downward at a 45 degree angle, pointing away from your pump but inside your pump pit. Make sure to disconnect your pump from the lines and place it in a place that is easy to drill.

Is there supposed to be a hole in my sump pump pipe?

A2. A weep hole is also considered a relief hole, this hole will prevent the pump from going into “air-lock”, air-lock is when the pump is running but not delivering water. We suggested that the weep hole be a 3/16” hole in the discharge pipe below your floor line between the pump discharge and check valve.

Why do you need a vent hole in a sump pump?

The vent hole allows excess air to escape from the pipe, preventing air bounding.

Does a sump pump drain need a vent?

Does a sump pump need to be vented? Not all sump pumps need to be vented but in areas with radon they will need a vent.

Do Wayne sump pumps need weep hole?

All sump pumps are the same right? WAYNE pumps also remedied the need for a weep hole, by developing a unique top suction design that pulls water from above the impeller, eliminating the risk of air locks, clogging and that pesky gurgle.

How do you keep a sump basin from floating?

Some contractors drill holes in the bottom of the sump basin and around the sides to allow excess water to enter and prevent the basin from floating up. If you choose to drill holes in the basin, make sure the holes are smaller than the “solids handling rating” of the pump (generally 1/4 in. to 1/2 in.

How deep is a sump pump hole?

The typical pit is 30 inches in depth and 18 to 24 inches across. The standard sump pit insert available in home improvement centers is 26 gallons and 18 inches diameter. In many cases the pit needs to be a minimum of 24 inches and up to a depth of 36 inches. But some builders just use a common 5-gallon bucket.

Should I drill holes in bottom of sump pump basin?

Is it necessary to drill holes in my sump basin? Yes – drilling sump pump basin holes is almost always needed! If you choose to skip drilling these holes you risk the basin ‘floating’ in the pit. This can cause damage to the pump as well as broken drain lines!.

What does a weep hole do on a water pump?

A weep hole is a small hole on the bottom of the water pump. Its main purpose is to warn you when the pump’s seals are about to fail. Automotive water pumps only have coolant seals, as the bearing is permanently lubricated.

Should you cover your sump pump?

While most sump pumps are effective in removing water, they should always be covered with a gas-tight lid to avoid moisture problems, as well as to prevent the seepage of radon into the home.

Why does my sink gurgle when the sump pump runs?

Gurgling noises are often caused when water flows back down the discharge pipe after the pump cycles. To reduce gurgling, upgrade your standard swing check valve with a spring loaded check valve. When your sump pit or basin is empty, the pump makes a sound similar to sucking liquid through a straw.

What does a failing sump pump sound like?

Normally the only sound a sump pump makes is a low continuous hum, but if it starts making loud and unusual noises, then it’s time for a repair. A rattling or grinding noise can indicate something wrong with the impeller or fan. Failure to turn on.

What is a catch basin sump?

Description. Deep sump catch basins, also known as oil and grease catch basins, are storm drain inlets that typically include a grate or curb inlet and a sump to capture trash, debris and some sediment and oil and grease. Stormwater runoff enters the catch basin via an inlet pipe located at the top of the basin.

Why is there gravel in sump pit?

Next, place the basin into the hole in the basement floor and then pour gravel around the outside of it. Add a little bit of gravel to the bottom of the pit. (The gravel will help boost the effectiveness of the filtration to keep debris out.) Take the sump pump and carefully submerge it into the water.

How far up can a sump pump push water?

For most average-sized homes in areas with average water tables, a 1/3 HP sump pump should be sufficient. Typically, 1/3 HP pumps can handle 7′ – 10′ vertical lifts from the sump pit if they have one 90-degree elbow and a horizontal pipe run between 3 feet and 25 feet.

How much water should be in sump pump hole?

If you are sizing your current sump pit for a sump pump, it’s important to know how much water it holds. As a general rule of thumb, for sump pits that are 18” in diameter, each inch of water equals around 1 gallon.

How far down should a sump pump drain?

Discharge Piping Depth You should install your sump pump discharge line 2 feet below The frost line in your County. This will help prevent the water in the pipe from freezing and causing clogs while still making it easy to dig and access the trench in case there are any problems.

How much area does a sump pump cover?

In that case, here are some general guidelines: On sandy soil, plan for a system capacity of 14 gallons per minute for every 1,000 square feet of home. In clay soil, plan for a system capacity of 8 gallons per minute for every 1,000 square feet of home.

How much gravel is needed for a sump pit?

Set the pit liner in the hole and fill the surrounding void with coarse gravel. A gravel aggregate of 3/8 to 1/2 in. in diameter will work well.