Table of Contents
Locate the condensate drain access point outside your home or near the indoor air handler enclosure. You should see a small vertical vent extension as part of the piping. The vent is located above the point where the line exits your air handler. Open the plug on top to access the drain lines.
Where do you drain the condensate on a furnace?
Most furnaces will have at least 2 internal drains, typically one for the heat exchanger and one for the vent, usually at the inducer outlet or on the inducer housing.
Can you drain condensate into sewer?
Should you be worried about an AC condensate drain into the sewer? A simple answer would be yes. An AC condensate line should never connect to sewage directly. This lets the sewage air enter your AC system.
Where Should 90% furnaces drain to?
Most “90%” furnaces will have at least 2 internal drains, one for the heat exchanger and one for the vent. One will be located at the inducer outlet or on the inducer housing. The secondary heat exchanger outlet is sealed inside a plastic part called the collector box.
Can furnace condensate drain outside?
A furnace produces condensate as it works (it’s part of the combustion process), and this condensate must be drained and removed to the outside. If the pipe that runs the condensate to the outside of the house freezes over, your furnace won’t be able to work!.
How many feet should a condensate line have a support in place of the drain line is more than 20 feet?
When a drain line is PVC, the IMC dictates that it should be supported every 4′ when horizontal (while maintaining proper pitch) and every 10′ vertically. IMC 307.2.
How far can you run a condensate line?
Generally speaking, linesets (the refrigerant lines) should be under 50 feet for best performance.
Can you drain a condensate line into a vent pipe?
Condensate disposal by connection to a plumbing stack vent pipe, is not recommended and is prohibited by building code in some jurisdictions. Be sure to check with your local building code compliance department.
Should condensate trap be full of water?
The boiler should never be operated without the condensate trap in place, as it prevents noxious combustion gases from travelling down the condensate pipe. Should the trap have to be removed from the boiler, it must be topped up with water when it’s replaced.
Does a condensate drain need a trap?
The only code requirements for drain lines removing condensate from HVAC equipment are: a) for the installation of a trap in accordance with the unit manufacturer’s installation and operating instructions; b) that the drain lines slope toward the final drainage point at a rate of 1/8 inch per foot.
How much water should drain from furnace?
A 90% or higher efficiency furnace produces around 0.8 gallons of condensate per hour of running. This equates to about five or six gallons per day of acidic water from condensation each day. Most of the time, the drain and drain line runs to outside the home and the condensate just seeps into the ground, harmlessly.
What is a condensate drain?
A condensate drain line is a line that runs through a home or building’s central air conditioning system and leads to the outside. Condensate lines are typically crafted with PVC pipe or metal, and they provide a funnel for the humidity and condensation created by air conditioner evaporator coils as the systems run.
Do condensate drains need an air gap?
Condensate drains from air conditioner coils, condensing furnaces, and heat-recovery ventilators should not drain directly into a DWV pipe. An indirect drain using an air gap should be installed. In some locations, the direct connection of a condensate drain line into a stack is not permitted, even with a trap.
What must be installed in the drain line to ensure proper condensate removal?
In order for this to be achieved, condensate must be removed quickly and efficiently through steam traps installed in proper condensate discharge location (CDL) installations. Steam traps can’t, however, simply be installed any which way and forgotten.
Does pumped condensate need to be sloped?
The waste pipe shall have a slope of not less than 1/8 inch per foot (10.5 mm/m) or one percent slope and shall be of approved corrosion-resistant material not smaller than the outlet size as required in either Section 310.3 or 310.4 below for air-cooling coils or condensing fuel-burning appliances, respectively.
What is the minimum slope allowed for 2 condensate waste lines?
Slope – The drain shall have a slope of not less than 1/8 inch per foot and shall be approved corrosion resistant pipe not less in size than 3/4 of an inch for air cooling coils and not less than the drain outlet size for evaporative coolers or other equipment. 2.
Can condensate drain to stormwater?
As per Figure 6, condensation drains can discharge to a floor waste gully via a tundish un-trapped, provided the discharge pipe is between 25mm to 50mm and no longer than 10m in length. The discharge to a sanitary system or stormwater system shall be as shown in Figure 7.
Can you run condensate into gutter?
It is possible to terminate a condensate pipe into a rain water down pipe that terminates into the foul waste system. As with all externally-run condensate pipes, it is recommended to keep the external run to minimum and the pipe diameter to 32mm when exiting the property.
