Table of Contents
What is a shower bead?
Designed to span gaps between drywall and substrates with an extra wide 2¼” mud leg. Uses significantly less mud than filling and paper taping large gaps, and offers a mold-free alternative to paper for use in damp areas such as around shower/bath enclosures. Also known as Oversized Tear Away L Bead.
What is a zip strip bead?
AMICO “ZIP STRIP” Ceiling “L” Trim has a removable masking strip that allows this bead to be finished without staining the adjacent ceiling. Perforations and ridges placed on all surfaces that receive finishing compound or veneer plaster assures excellent adhesion.
What is tear away bead used for?
Tear away beads are designed for finishing the rough edges of drywall to provide a clean, smooth line at the edge of the board.
Which is better paper or metal corner bead?
Paper-faced corner bead makes taping outside corners a snap Outside drywall corners have traditionally been protected with nail-on metal corners, but paper-faced corner bead is simpler and resists cracks and chips better.
Which is better metal or vinyl corner bead?
Vinyl beads are inarguably superior to metal beads in two important ways: vinyl is dent-resistant and rust-proof. In contrast, vinyl beads excel in damp, moisture-prone areas. They are impervious to rust and water damage, so they will stand the test of time without damaging or discoloring the finished wall.
What is J bead?
J-Bead is designed to cover raw edges of drywall under all window and door casing. Rigid vinyl is not a thermal transmitter and helps stop condensation where gypsum board terminates at exterior metal surfaces, such as window frames and mullions. Rust proof and dent resistant.
What is corner bead?
Corner bead is a material that is used on the corners of walls in drywall construction to make the corners crisp and professional looking. Drywall corner beads are often used between the ceiling and the walls as well as in corners. Metal and plastic are both used in the manufacture of corner bead.
Is Trim Tex paintable?
All our vinyl drywall accessories are 100 percent paintable, without requiring any surface treatment. We recommend using a high-quality paint to finish our products for the best results.
Should I caulk between shower and drywall?
Shower stalls usually have a flange that gets nailed to the studs, and its outer edge gets covered when you install drywall. This leaves a gap between the edge of the drywall and the stall that you have to fill with silicone caulk, using a caulking gun.
What can I put behind my shower surround?
Use an appropriate waterproof or moisture-resistant backing material behind grouted tile or stone or segmented plastic or fiberglass tub and shower surrounds. Appropriate materials include cement board which has a cementitious core and glass mats on both sides to strengthen the board.
Do you need to tape over corner bead?
Taping the metal corner helps to prevent cracks. Cracking along the edge of metal outside corner beads is a common problem. If you don’t want to go shopping for special corner bead, avoid future cracking by applying paper tape over the metal edge after you’ve nailed on the bead.
What is the best corner bead to use?
The most common and least expensive corner bead is galvanized metal. Easily applied with your choice of nails, screws, staples, compound or adhesive, it resists rust and stands up well to minor abuse once installed.
Do you put mud under corner bead?
The first coat of drywall mud should be applied to corner bead after the drywall taping has been done. The second coat can be done either after the seams have been taped and coated or after the seams have been final coated.
Can I use drywall screws on corner bead?
Hold corner bead firmly in place and affix with drywall nails or screws, every 10 to 12 inches. Slightly dimple each fastener. Using a 4″- 6″ drywall knife, apply a generous coat of drywall joint compound to each side.
Can you screw vinyl corner bead?
Make sure that the bead is installed straight and attached firmly. Family Handyman says installing vinyl corner beads with screws is the most common way to install corner beads because it is thought to be more durable and sturdier. It is a more involved process and can be used for metal corner beads as well.
Do you use corner bead for inside corners?
The answer, though, is simple: They cheat. They use a rigid material called corner beading, which can be made of metal or plastic. Inside corners don’t need as much protection, so drywallers cover them with regular drywall tape. The process for finishing inside and outside corners is the same.
Can I use mesh tape for inside corners?
You can use mesh anywhere except inside corners. But mesh tape has one weakness (literally): It’s not as strong as paper. To compensate, you have to cover it with setting-type joint compound, which is stronger than premixed compound (see tip below).
Can you paint J bead?
Generally, it is a personal preference whether you want to mud the J-bend corner, sand it and paint it, or to not use mud and just paint over it. However, if you are installing the J-bead in a spot where there will be a lot of vibration present, i.e., by a door, you would NOT want to use mud on it.
What is J trim used for in drywall?
Fry Reglet J Molding is a basic interior or exterior trim used to terminate and finish plaster, stucco, drywall or wood panels.
