Table of Contents
Does Walmart sell furnace ignitors?
Furnace Ignitor for 025-32625-000 Igniter – Walmart.com.
How much does it cost to replace a furnace ignitor?
Here’s the bottom line: Whether for a natural gas furnace, oil, or a propane furnace, replacing a furnace ignitor–including parts and labor–will cost you around $300 – $425 for a qualified contractor to install. Compare that to, say, a draft inducer motor, which will cost $400 – $1,500 to replace.
How do I know if my furnace spark ignitor is bad?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
Are furnace igniters interchangeable?
Furnace hot surface ignitors or glow plugs are found on most furnaces to light the gas flames upon furnace start-up. Like a light bulb, they are a regular replacement item. Most ignitors are interchangeable as long as they fit in the furnace space provided.
How much does an ignitor cost?
Igniter Cost: The igniter costs no more than $30 to $50. Check with your furnace manufacture for the model number of your furnace so you can find the right igniter for your unit. Furnaces can last for several years, and hence it is not hard to find the right replacement part.
Should I replace my furnace ignitor?
Don’t worry—an ignitor that goes bad is common for most furnaces. Fortunately, you can replace the ignitor without replacing the full furnace. Most ignitors last about seven years. Keep reading to learn how you can tell if your furnace problem is a faulty ignitor.
Why is my furnace ignitor not working?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
How often should furnace ignitor be replaced?
According to the Gas Furnace Guide, ignitors have an average lifespan of four to seven years. So, after about seven years, you may have to replace the ignitor; however, you probably won’t have to replace the entire furnace because other parts, such as the heat exchanger, can last more than 15 years.
Can you clean a furnace ignitor?
If your furnace has a spark ignitor and it’s working haphazardly, it too could be covered with soot, and a blast of compressed air may be enough to clean it. Compressed air can also clean a blocked pilot tube that is causing the pilot flame to burn weakly or not at all.
Why does my furnace igniter keep clicking?
The ignitor will keep clicking as it tries to spark a flame. This could indicate a dangerous gas leak or clogged gas valve. This might be caused by faulty gas meter controls or the thermostat controls. If a gas furnace runs and then shuts off, or short cycles, this indicates an inconsistent flow of gas.
Are all hot surface ignitors interchangeable?
And each brand has different models. Within the same brand they might be more similar but no guarantee. And what makes matters worse is that the igniter you are replacing is probably broken. So if it was a hot wire igniter you won’t be able to compare the resistances to a new one to see if they might perform similarly.
Where is the ignitor on my furnace?
Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.
How long do furnace ignitors last?
No matter which type of ignitor is in your furnace, this chain of events lights your heater so that it blows hot air. Don’t worry—an ignitor that goes bad is common for most furnaces. Fortunately, you can replace the ignitor without replacing the full furnace. Most ignitors last about seven years.
Are furnace ignitors universal?
This universal ignitor is a replacement part for use in gas-fired appliances like furnaces, water heaters, and boilers, compatible with over 150-OEM models.
How much are furnace ignitors?
Igniter Cost: The igniter costs no more than $30 to $50. Check with your furnace manufacture for the model number of your furnace so you can find the right igniter for your unit. Furnaces can last for several years, and hence it is not hard to find the right replacement part.
How do I know if my ignitor is bad on my furnace?
Your furnace won’t run: The most obvious sign that your ignitor is bad is that it won’t ignite, and this generally manifests itself in your furnace failing to run when you activate it. One word of caution, though: this can also be caused by other issues, some of which are electrical.
Are all furnace ignitors the same?
Most ignitors are interchangeable as long as they fit in the furnace space provided. Select your ignitor by looking at the one you have, and comparing it to the photos of ignitors here; select the one most similar.
