Table of Contents
What board do you use for fascia?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
How much is a piece of fascia?
Fascia Board Prices. Fascia boards are typically sold by the linear foot for a cost between $1 and $20 per foot, depending on the type of material. Fiber cement is sold by the square foot, between $1 and $5.
What can I use instead of fascia board?
Vinyl. Vinyl siding is a common alternative to fascia board. This type of rafter facing does not rot or wear as quickly as fascia board under the same weather conditions.
How thick should a fascia board be?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
Can PVC be used for fascia board?
Obviously the biggest reason for using a PVC trim board is long term maintenance combined with traditional architectural appeal. PVC trim boards will not rot, twist, split or warp. In addition you can leave it unpainted if you like or paint it to match a certain color scheme.
How long do fascia boards last?
Well installed and maintained wooden fascia can last for up to 20 or 30 years, before they start deteriorating. Although some might need replacing within 5 to 10 years.
How much is it to replace fascia boards?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
Can plywood be used for fascia?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
How do you fix rotted fascia?
Soffit and Fascia Repair Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. Remove Rotted Fascia. Remove the rotted section of fascia. Remove Old Soffit. Pull down to remove the old soffit. Remove Rotted Rafter. Attach Cleat. Attach New Rafter. Seal Replacement Soffit. Attach Replacement Soffit.
Can I use pressure treated wood for fascia?
It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
What is Hardi Senepa?
HardieFlex® Senepa 9.0mm is a versatile fascia board suitable for all types of houses. It can be used to highlight intricate roof designs and it operates as backing for gutter systems to prevent water and vermin from entering the structure through the eaves line. It is fire-resistant and deemed to be non-combustible.
What is Friezeboard?
Frieze board is a type of trim that is typically installed between the top of a home’s siding and the soffit. It’s normally installed flat against the home, but it may be installed at an angle if installed on a gable. Frieze board may also be used as a decorative, horizontal trim anywhere in or on the home.
Is Hardie trim discontinued?
While your preferred siding brand may have discontinued production for some of their products, you should not be afraid as many options are available. For instance, recently, James Hardie has discontinued their trim supply in 2021 for the Pacific Northwest.
Can cement board be used as fascia?
Soffits and fascia board We used fiber cement board to close in the soffits and cover the fascia of the house. Any rotted fascia boards should be replaced prior to covering. The fiber cement board, although durable, is not structurally adequate to support the eaves on its own.
Can you put fascia over existing wood?
Hi yes you can buy upvc capping fascias and soffits. However you must make sure that the original woodwork is of sound condition. As you shouldn’t cap over any rotten wood. And make sure that you use starter trim to fit the soffits.
Can you use 2×6 for fascia?
Around here everyone uses 2×6 fascia and then covers it with aluminum fascia. If you are leaving the fascia as wood to be painted then the finished face board is better to wider. So you could use 2×4 frame work and 5/4 or 1×6 fascia boards.
