Table of Contents
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do I reset my furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
Should I hit the reset button on my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
Where is my furnace blower motor reset?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
Where is the furnace switch located?
Most building codes require a furnace switch or “disconnecting means” within sight of the furnace itself. It’s usually mounted on the side of the furnace or a wall nearby.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
How do I reset my furnace thermostat?
Reset the Thermostat The method to reset your thermostat will vary depending on the model. Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
Why is my furnace reset button not working?
Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. Dirty flame sensor rod: Every now and then, the flame sensor rod gets dirty and shuts the furnace off. Make sure you wipe it off regularly. Low fuel: Low fuel is also a common cause of burner failure.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
Why is my furnace not heating?
Dirty filters are the most common cause of furnace problems. Dust and dirt restrict airflow—and if the filter gets too clogged, the heat exchanger will overheat and shut off too quickly, and your house won’t warm up. If the blower is running but no heat is coming out, replace the filter.
How do you manually reset a furnace?
Follow these simple steps: First, turn off the power supply to the furnace by turning off the breaker in the circuit box. Locate the reset button on the furnace and press it to reset the furnace. If the button is popped up, press it down. Return the cover to the blower compartment and turn the power on.
What does blower motor reset button look like?
If you use central heat and air, the button is likely located in the air handler’s compartment on the blower motor, and it will be either red or yellow. It usually lays flush with the surface of the blower motor until triggered by the internal overload protection circuit.
Why is my furnace fan not running?
Inspect the Wires in Your Furnace Make sure that the power cord hasn’t melted or a fuse hasn’t been blown. If your cables are looking fine, try unplugging the fan for a few minutes and then plugging it back in again. If unplugging and plugging your fan back in again doesn’t work, check the fuse box.
Why is my furnace not lighting?
If your furnace won’t ignite, the source of the issue may be a broken flame sensor. The sensor is responsible for turning off the gas burners to avoid gas buildup. Once this component starts to malfunction, it may stop the burners from igniting altogether. Have an HVAC technician replace the flame sensor.
What does a furnace switch look like?
Furnaces have another switch, simply known as the “furnace switch.” It’s a power switch that often looks like a regular light switch. It can be located either on the unit or—because electricians often work before the furnace is installed—on a wall nearby. Often this switch is unlabeled.
Why is my furnace not starting?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
