Table of Contents
The Sync Module has a physical reset button located next to the USB port on the side of the device (pictured below). This button should only be used to put your Sync Module into setup mode. Pressing this button will bring your system offline until you reconfigure your Sync Module.
Where is the blink module reset button?
The reset button is located on the right-hand side of the Sync Module next to the USB port. Please note that this could take between 15-30 seconds. This will cause the Sync Module to reboot into setup mode.
How do I get my blink module back online?
Tap the banner to reach the Sync Module Offline screen. Follow the suggested steps from the Sync Module Offline screen. Verify Wi-Fi connection is working: Reboot the router and wait for internet to return. Verify your Sync Module is displaying a solid green and solid blue light.
Where is the reset button on the blink outdoor camera?
You can reset the blink camera by pressing and holding the reset button on the sync module. Once the light turns red, you have to delete and reinstall the sync module in the Blink App. , you can find the reset button at the bottom of the camera.
What happens if I unplug my Blink Sync module?
When the power goes out or your Wi-Fi drops (often for no good reason), your Blink cameras can become disconnected. Therefore, you may need to reset your Sync Module to reconfigure its network connection. This reset will allow you to reconfigure your device settings and prompt you to put in new Wi-Fi credentials.
How do I sync Blink module?
To add a Sync Module, navigate to the Home screen and tap the “add device” + button in the upper right. You are sent to the Add Device screen. 6. Tap Blink wireless camera system.
How do I unregister Blink module?
Tap the settings icon in the home screen’s footer. Select the system that contains the Sync Module you want to remove. Tap on Sync Module. Choose “Delete Sync Module” and then OK.
Why is my Blink system not working?
If one of your Blink cameras isn’t responding, you may see error messages like “Camera Busy” or “Thumbnail Failed”. Wait two minutes for Internet service to be restored, then try using your camera again. Power cycle your camera. To do this, remove the batteries for 10 seconds and reinsert them.
Why does my Blink Sync module keep going offline?
If you receive a “Camera Offline” notification that “Your Blink Mini is offline”, it means the Blink servers no longer have communication with the camera. The first, is to check the Wi-Fi internet and the power supply, then check the camera power connection.
Why is the blue light flashing on my blink module?
The blinking blue light indicates that your camera has already acquired the router information, but the network is poor. You can try as following: Reboot your router.
Does Blink Sync module need to be plugged in all the time?
Answer: Hello! Blink cameras cannot function without an active WiFi connection or an online Sync Module. If internet connectivity is lost or if the Sync Module is powered off, the system will go offline until it both are restored.
What does the red light on blink camera mean?
The red light appears when you first insert batteries. If the red light is not visible, make sure the batteries are fresh. It is also possible to see a brief red flash during motion detection. When the batteries are failing, the camera LED flashes Red 5 or 6 times after the Blue recording light goes out.
What is the USB port on Blink Sync module for?
The Sync Module has a USB port as well, we intend to release a firmware update for it that will allow video clips to be stored locally in the sync module rather than in the cloud. The camera has a micro-USB port for power in case you don’t want to run the camera with batteries.
How do I update Blink firmware?
How to update Blink firmware Download the blink_update. Connect the flash drive to one end of the USB OTG Cable and the other end to Blink. Finally connect the last end of the cable to a power source such as a mobile phone USB charger/USB battery pack/Laptop, etc. Blink will start the update immediately.
Why is my blink module not connecting to Wi-Fi?
Restart your device, or try switching the Wi-Fi setting off and on again to establish a connection. Make sure your mobile device is within range of your router or access point. Check that your router and any access points are powered on. Restarting your Wi-Fi router may also resolve this issue.
What is the difference between Blink Sync module and Sync Module 2?
The main difference comes with the upcoming Blink Subscription Plan and with the Blink Sync Module 2. Unlike older Sync Modules, the new version has a USB port for local storage, an attempt to appease customers who don’t want to pay for cloud storage.
How do I change my blinking WIFI?
To start, tap on the gear icon in the bottom row of the app to enter Account Settings. Then tap on the name of your system under System Settings. Tap on Sync Module to see the status screen, and tap “Change Wi-Fi Network”.
Can Blink Sync module be placed outside?
Yes, the Sync Module 2 works as a traditional sync module and works with all generations of Blink cameras from our original Indoor (gen 1), XT, and XT2 – to the new Blink Video Doorbell, Indoor (gen 2), Outdoor, and Mini. When an older camera is set up on the Sync Module 2, it uses 7200 seconds of Basic Cloud storage.
Will any USB flash drive work with Blink?
No matter what generation USB 3.1 you have (USB 3.1 Gen 1 or USB 3.1 Gen 2), it will work with the Blink Sync Module 2. The Sync Module 2 has a USB 2.0 Type A port. The USB standard is backwards compatible, meaning all USB drives can be used with the Sync Module 2, so long as the size is between 1GB and 256 GB.
What is the difference between Blink Module 1 and 2?
With Module 2, you can either view your video clips on the Blink Home Monitor app or plug your drive into your computer and upload any clips you wish to save. For comparison, the Blink XT2 ships with the Sync Module 1, which offers free video cloud storage but has no local storage option.
How does blink USB work?
Blink Local Storage saves clips to your USB drive when it is inserted into a Sync Module 2. The USB drive must be from 1 GB to 256 GB in size. The USB drive must have more than 375 MB of free space. If needed, you are asked permission to reformat the drive when it is first inserted.
