Table of Contents
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How do I reset my furnace?
How to Reboot a Furnace Change the Filter. Before you do anything, check the furnace filter. Check the Pilot Light. If the pilot light is off, your furnace can’t get the spark necessary to light the boilers. Turn the Furnace Off and Back On Again. Call a Certified HVAC Professional.
Should I hit the reset button on my furnace?
The purpose of the reset button on a furnace is to shut it down before it can trip your circuit breaker. The need for this may arise if the furnace becomes too hot, or if there is some sort of electrical system interruption. To get the furnace working again, you simply press the reset button back down again.
How do I reset my electronic ignition furnace?
To reset the ignition control module on an electronic-ignition furnace, turn down the thermostat or turn off the power switch. Listen for the sound of the spark or watch for the hot surface ignitor to glow. Next, make sure the furnace’s flame sensor is clean.
What does blower motor reset button look like?
If you use central heat and air, the button is likely located in the air handler’s compartment on the blower motor, and it will be either red or yellow. It usually lays flush with the surface of the blower motor until triggered by the internal overload protection circuit.
How long does it take for furnace to reset?
Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too. Never touch the breaker with wet hands and use only one hand to do it.
How do you reset a furnace blower motor?
How to Find and Reset your Furnace Motor Blower Step 1: Turn off the power to the furnace. Step 2: Remove the blower compartment cover. Step 3: Make sure the blower is completely cooled off. Step 4: Locate the reset button. Step 5: Press the button in (assuming that this is your issue and that the button has popped).
How do I reset my furnace thermostat?
Reset the Thermostat The method to reset your thermostat will vary depending on the model. Common methods for resetting a thermostat include installing the battery backward for five seconds, pushing a recessed reset button with a pin or paper clip, or shutting off the breaker to the thermostat for 30 seconds.
How many times can I hit the reset button on my furnace?
Don’t hit “reset” more than twice. The process pumps oil into the burner chamber, where it can accumulate if you have no ignition. Then when the furnace finally does start, it can do so explosively. So if the button won’t reset, or quickly pops up again, it’s time to call a professional repair service.
Why is my furnace reset button not working?
Obstructed airflow: Sometimes the reset button gets tripped because the furnace isn’t receiving enough airflow. Dirty flame sensor rod: Every now and then, the flame sensor rod gets dirty and shuts the furnace off. Make sure you wipe it off regularly. Low fuel: Low fuel is also a common cause of burner failure.
Why is my furnace not starting?
Ensure your furnace filters are clean: Your furnace won’t start up if it does not get enough airflow. Check your pilot light: If you have a gas furnace and gas supply is stopped your pilot light will go out. Check your blower motor: If the blower motor is not working then your furnace won’t pump out warm air.
Can hear your furnace click on but it does not fire up?
The Pilot Light (Faulty Ignition Sensor) The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. This is typically the problem if you can hear your furnace click on but it does not fire up. If the sensor or ignitor is dirty, it will need to be cleaned.
Why is my furnace not lighting?
If your furnace won’t ignite, the source of the issue may be a broken flame sensor. The sensor is responsible for turning off the gas burners to avoid gas buildup. Once this component starts to malfunction, it may stop the burners from igniting altogether. Have an HVAC technician replace the flame sensor.
Why is my furnace running but not blowing air?
Check Your Furnace Air Filter Next, check your heater’s air filter, as this can cause a furnace to stop blowing air. Your filter could be so saturated with dust and debris. In that case, even though the furnace is actually blowing air, your clogged filter is blocking it from making it into your ducts.
Where is the furnace switch located?
Most building codes require a furnace switch or “disconnecting means” within sight of the furnace itself. It’s usually mounted on the side of the furnace or a wall nearby.
How long does it take for a furnace to start blowing hot air?
Your furnace should start blowing warm air within 15 minutes. After that, if the air still feels cold, there could be another system issue on your hands.
Where is furnace blower reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
