Table of Contents
Some types of fireplaces have a round, decorative slot for controlling the gas valve. It’s usually located near the fireplace, usually to the immediate left, right or on the floor. You will control the gas flow with a fireplace key (sometimes called a hex key) as you light the fireplace.
Where is the gas valve on a gas fireplace?
Each gas appliance should have a gas line running to it that will have a valve located just before the appliance. This valve will likely resemble the valves on your gas main and can be operated by turning the valve to sit either in line with the pipe when the gas is on, or perpendicular to the pipe when the gas is off.
Where is the gas shut off valve?
Your main shut off valve is located just before the gas meter. This is called your “street side valve”. On the inside of your house, where the pipe enters your house, you can find your “house side valve.” This ball valve is attached to a black iron pipe.
How do I know if my fireplace has a gas valve?
One way to test if your main control valve is bad is by testing resistance. We can do this with our Digital Multimeter. First, find you need to find “Zero” but touching your multimeter leads together. If it reads anything other than zero, you’ll want to subtract this number from the number you will read on the valve.
Where is my gas fireplace switch?
First, locate the fireplace controls, they are located usually behind a louver or panel at the bottom of the fireplace. Next, locate the control knob on the gas valve, it usually has 3 labels Off, On, and Pilot. You will also want to locate the ignitor button; it looks very similar to a starter on a barbecue grill.
What does a gas valve look like?
Main Gas Shutoff Valves The valve will usually look like a small rectangle, and you’ll need a special wrench to turn it. When it’s open, the long side is parallel to the incoming gas pipe. To stop the flow of gas, close the valve by turning it perpendicular to the incoming line.
How much does it cost to replace a gas valve on a fireplace?
A furnace gas valve replacement costs $200 to $800 on average. Furnace gas valve prices are $75 to $300 for the part alone or up to $600 for original manufacturer parts (OEM). Gas valve replacement labor costs $125 to $500.Furnace gas valve replacement cost. National average cost $500 Minimum cost $125 Maximum cost $1,000 Average cost range $200 to $800.
Why is my gas fireplace not getting gas?
Check your breaker box and reset any tripped breakers you come across. Gas Valves: Make sure that your gas valve is open and in the on position to ensure the flow of gas to your fireplace. If turning the knob to the on position doesn’t open the gas flow, contact your propane supplier. The tank may be exhausted.
How long do gas fireplace valves last?
Gas fireplaces are appliances, and like any other appliances, they have an expected lifespan for parts and for the entire unit, depending on the type of appliance, location, amount of use, etc. Thermocouples, thermopiles and pilot assemblies usually last at least five years, and control valves seven to ten years.
Why won’t my gas fireplace turn on when I flip the switch?
What can happen over the years, is that the connections inside the switch can get dirty, corroded, or broken, causing a loss of this voltage at the switch. So by the time the small amount of voltage gets sent back to the fireplace, it is not enough to signal the fireplace to turn on.
What are the two switches on a gas fireplace?
Question: There are two wall switches on the wall beside the gas fireplace. The top switch ignites the flame.
Should I turn off the pilot light on my gas fireplace in the summer?
Your Utility Bill Perhaps the most important reason to turn off gas fireplace pilot light in summer is because of the money and energy you will be saving. If you leave the pilot light on during the summer it is simply sitting there burning gas, which is wasting gas and contributing to an exorbitant energy bill.
What causes gas valve failure?
The valve itself may have simply worn out or may be damaged due to basement seepage or submersion. Alternately, one of the electronic gas ignition components or a glitch in the safety circuit may be to blame. If your furnace has a standing pilot light, the thermocouple could be worn out.
Can I replace my own gas valve?
By watching how someone else does it, you can ensure that you don’t make any mistakes when changing the valve. There you have it, a DIY guide to replacing your furnace’s gas valve yourself. Most of the time the replacement process tends to be fairly straight forward.
Can a gas valve be repaired?
The gas valve cannot be repaired in the field. Only the gas valve manufacturer or someone certified by the manufacturer of the gas valve can make repairs. Then re-certifying the safety of the gas valve. This also applies to gas valves that have been submerged underwater due to flooding.
Why wont my gas fireplace shut off?
Step 2: Turn off the power switch if your gas fireplace won’t turn off. If there is no switch, it could be on the wall near your fireplace or elsewhere in the room. If there is no switch, you will need to turn the power to the fireplace off in the breaker box.
Is valve open or closed?
When the handle is parallel to the valve, it is closed, and when it is perpendicular to the valve, it is open.
Is it safe to turn off gas valve?
In an emergency, your gas can be turned off at the main gas service shutoff valve. Do not shut off the gas unless you smell gas, hear gas escaping, see a broken gas line or suspect a gas leak.
