Table of Contents
The drain hose is usually found on the back of the washer, along with two separate hoses for both cold and hot water supply. The drain hose carries wastewater out of the machine, while the hot and cold water supply hoses bring clean water in.
How do I know if my washing machine drain hose is clogged?
If the hose is clogged, it can prevent the water from being pumped out of the machine. To test this, remove the drain hose attached to the washer and make sure it is clear. An easy way to check that the drain hose is clear is to blow air through it.
How do I remove the drain hose from my washing machine?
To disconnect a washing machine, turn off the water valves located behind the washing machine by turning them clockwise. Next, pull the machine away from the wall and unplug it. Place a bucket behind the machine to catch water drainage, then turn the ends of the hoses counterclockwise to detach them from the wall.
Where is drain hose?
The drain hose runs from the pump to the sink drain, or to the air gap on top of the sink. There is a second hose leading from the pump that is a recirculation hose. When you are checking the drain hose for a blockage, you should check the recirculation hose as well.
How do you manually drain a washing machine?
If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
Where is the P trap located?
The P-trap is the P-shaped section of pipe in the line that runs from the bottom of your sink to the wall. It’s shaped this way to trap sewer gasses and prevent them from coming out the sink as well as to catch debris that’s been washed down the sink, such as hair or food scraps.
Where is the drain on a Whirlpool washing machine?
Remove the panel. The drain pump assembly is directly in front of you, in the middle of the machine. Unscrew the knob on the drain pump by turning it counterclockwise. Hold a bucket in front of the pump while you remove the knob to catch the water.
Do washers come with drain hose?
The drain hose will come attached to your washing machine and should feed into either a nearby sink or a standpipe. If you are feeding the drain hose into a sink, attach a plastic hose guide to keep the hose bent downward into the sink without kinking.
What does drain mean on a washing machine?
What Does the Drain Function on a Washing Machine Do? It removes the water from the tub during the spin cycle. The washer pump forces water from the bottom of the machine into the drain hose. The drain hose loops to the top of the machine, and then down to the drain, enabling the tub to fill.
What causes a washing machine not to drain and spin?
If the washer won’t drain or spin, either something is stuck in the washing machine drain hose or pump, or the pump is broken.
How do I know if P-trap is clogged?
A blocked p-trap will cause water backflow to occur. The first sign that your p-trap is clogged is when the water in your sink takes longer than average to flow down the sink. In the case of a clogged P-trap, it is best to place a small bucket under the trap with the water shut off.
How often replace washer drain hose?
Replace your washing machine hoses every three to five years. Install a water hammer arrestor, which helps absorb the shock of water that increases pressure within the hose after the washing machine cycle ends. Turn off the water supply to washing machines when they aren’t in use.
How do I manually drain my Whirlpool washer?
If not, follow these steps: Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose at the back of the washing machine. Step 3: Drain the water. Step 1: Turn off the power and lay down towels. Step 2: Locate the drain hose. Step 3: Drain the water. Step 4: Scrub the filter.
How do you drain a Whirlpool front load washer?
How to Drain a Front-Loading Washing Machine STEP 1: Turn off the power. Switch the power button off, if your model has one. STEP 2: Locate the drain pump filter and/or drain tube. STEP 3: Drain the water. STEP 4: Clean the filter. STEP 5: Know when to call in a pro.
Where is the filter on my top loader washing machine?
Top Load Washer – Lint / Pump Filters There are 2 crescent-shaped Fine Mesh plastic lint filters in the bottom of the wash basket under the agitator. During drain down and spin, the water forces the lint off the bottom of the filters and down the drain. These filters should never require cleaning or replacement.
Where is the drain pump filter on my Whirlpool Duet?
The location of the drain pump filter in a Whirlpool Duet washer is accessible through the lower access panel below the washer door.
How do you hook up a washer and washing machine to the same drain?
Connect the Sink and Washing Machine Insert the drain hose from the washing machine into the top of the sewer pipe. Fit together the p-trap and drainpipe and place them into position between the tailpiece and the sewer pipe. Connect the drainpipe for the sink to the tee inlet.
