Table of Contents
Near the bottom of your furnace is a switch that normally says “Pilot,” “On” and “Off.” Find this switch and turn it to the “Off” position. Wait at least five minutes. This is important because it gives the gas time to dissipate, which is necessary to avoid possibly starting a fire.
How do I light the pilot on my furnace?
How Can I Restart My Pilot Light? Step 1: Turn off your furnace. Step 2: Locate your gas valve. Step 3: Hold down the red button. Step 4: Light the pilot light. Step 5: Let go of the button. Step 6: Turn your gas back on. Step 7: Turn your furnace back on.
Does every furnace have a pilot light?
Newer gas furnaces (since about 2010) do not have a traditional pilot light that burns all the time. Instead they use electronic ignition systems that light only as needed. So, if you’re looking for a pilot light on your newer furnace and can’t find one, it might be because you don’t have one.
How do I know if the pilot light is out on my furnace?
Just follow these steps: Remove the front cover panel on your furnace. This should expose the pilot, which simply looks like a small single burner, kind of like a candle or if you only had a single flame lit on a gas stove. If there is no flame, then the pilot is out.
Can I relight the pilot light by myself?
If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.
How do I check my pilot light?
How to Tell If the Pilot Light Is Out Locate the front cover panel on your furnace. It should be a little door that’s easily visible. If your pilot light is on, it should be easy to see – your eyes will be drawn to the little flame. If you don’t see a flame, your pilot light is out. If there is a flame, check the color.
How do you reset the pilot light on a furnace?
Turn the knob to “Pilot” and hold down the “Reset” button. Using a long lighter, bring the flame close to the pilot opening. This should ignite the pilot light. Once the pilot is lit, you can release the reset button. The pilot should stay lit at this point.
Does Central Heat have a pilot light?
There is no pilot light to go out on a central gas heater — and no chance of gas escaping into the room — which also means you cannot ignite the burner manually. From time-to-time, the gas heater may require restarting to engage the igniter and burners.
Why is my furnace not lighting?
If your furnace won’t ignite, the source of the issue may be a broken flame sensor. The sensor is responsible for turning off the gas burners to avoid gas buildup. Once this component starts to malfunction, it may stop the burners from igniting altogether. Have an HVAC technician replace the flame sensor.
What does the pilot light look like?
A proper pilot flame should be blue with a yellow tip and should be strong enough to cover about 1/2 inch at the end of the thermocouple tip. If the flame is too strong and improperly adjusted, it will be blue but may be noisy and lift off the thermocouple, causing improper furnace operation.
What can cause a pilot light to go out?
What Causes A Pilot Light To Go Out? Age & Condition Of Heating System. If your gas or propane furnace has a standing pilot light, there’s a good chance that it is 20+ years old. Cracked Heat Exchanger. Gas Valve & Gas Supply Issues. Thermocouple Malfunction. Improper Venting & Airflow.
How much does it cost to relight a pilot light?
Most service providers will charge a standard fee per visit that typically covers the cost to relight a gas water heater. This service call price can range from $80 to $100.
Why is my furnace not blowing hot air?
First, check to make sure the thermostat is set correctly. You will want to make sure that the fan control is set to auto, and not ‘on’. If the thermostat appears set correctly, turn off your heater at the thermostat and check the filter. If the filter is dirty, replace it.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard, and requiring immediate repair.
How do I turn my gas back on after disconnecting?
You are going to need a wrench or gas shut off tool to do this. Very slowly, turn the meter back into the on position. The lever should be in line with the pipe after making a ninety-degree turn. Finally, you can re-light any of the pilot lights in your appliances.
What do I do if my pilot light won’t light?
If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.
Should the pilot light always be on in a gas furnace?
Most furnaces with electronic ignition have a device called a hot surface igniter. The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.
