Table of Contents
The blend door actuator(s) are typically located on the climate control case behind the dashboard.
How do I know if my blend door actuator is bad?
If you hear a droning or squeaking sound coming from the center of your dashboard, there is most likely something wrong with your blend door actuator. These sounds will usually get louder when you turn on your AC or change the temperature.
Where is my blend door located?
The blend door is a plastic box located on an under-trim panel, responsible for sending cool or warm air within the vehicle to keep the passengers comfortable. You might need warm air when the vehicle is cold or vice versa; when you turn the climate control dial, the blend door will have to send in the desired air.
Can you manually move the blend door actuator?
The actuator is what needs replacing. The arm/hinge that is moving up and down is just the thing you need to grab with your finger to manually flip the blend door over to the hot temp side.
What happens when blend door actuator fails?
Incorrect Climate Control Outlet Temperature A faulty actuator can cause the blend door to be stuck in one position or another, resulting in an outlet temperature that’s hotter or colder than the desired setting.
Where is actuator located?
The AC actuator is located above or below the coil. It can be set to either single speed or variable speed. When it is not working properly, your AC will be ineffective, and your power bills can skyrocket.
Does the blend door actuator have a fuse?
The blend door actuator fuse in Your 2010 Ford F-150 can be found in the fuse panel that is located in the passenger’s footwell. The panel can be found behind a plastic door that has fuse written on it. The blend door actuator controls the blend door’s position.
Will a blend door actuator cause no heat?
If the door moves easily, then the problem is in the blend door actuator or the heater control head. If the motor fails when the door is closed, that could cause a no heat in car condition. During air conditioning season, a bum blend door actuator can fail in a full or partially open position.
Does the blend door actuator control hot and cold?
The blend door actuators, also called HVAC actuators, control the position of the vents that control the flow of air into your vehicle’s passenger area. When the actuator is not working, you will get either hot air but no cold air, or cold air but no hot air.
Does the blend door need to be open or closed for heat?
There are just flaps inside the ducts, called blend doors, operated by vacuum motors, that open and close to allow heat or stop heat from coming through the vents into the passenger compartment. And it sounds like one of your blend door motors is no longer working and that door is stuck in the open position.
How much does it cost to replace blend door actuator?
Blend Door Actuator Replacement Cost The blend door actuator usually costs between $100 – $300 depending on the car’s make and model, before labor costs. On average you can expect to pay around $150 for the actuator itself.
How long does it take to fix a blend door actuator?
Expect the replacement work to take one to two hours, including testing.
Why is my car blowing hot air on one side and cold air on the other?
Blend door actuators are the most common reason for the car air conditioning to blow cold air on one side and hot air on the other. They can be diagnosed with an advanced scan tool. If it does not move with the adjustments and commands, there is a problem with the blend door actuator and it will need to be replaced.
How much does it cost to replace actuators?
The Best in Auto Repair The average cost for HVAC blend door actuator replacement is between $312 and $359. Labor costs are estimated between $182 and $230 while parts are priced at $130. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.
Why is my AC cold on one side?
Due to the design of dual AC systems, low refrigerant is the leading cause of drastic temperature difference from one side of the dash to the other. In most cases after the proper charge of Freon is in the car, the temp will blow equally as cold like it should on BOTH sides!Dec 27, 2019.
Why is my AC vent blowing hot air?
When the cooling system’s filter is dirty, the air conditioner cannot properly move air through the system. This issue strains your air conditioner and can cause an AC to blow warm air. When determining what’s wrong when your AC isn’t properly cooling your home, first check your air filter to ensure it is clean.
How do I reset my blend door actuator Ford?
First thing You will need to do is remove the fuse for the actuator from the fuse panel in the driver’s footwell. After that You will want to start the car and run the AC system for a few minutes. Finally shut off the car and put the fuse back in and see if the blend door works.
Where is fuse for blend door actuator on 2011 f150?
To locate the actuator’s fuse, visit the interior or cabin fuse box. It should be found on the right hand side of the truck in the passenger’s footwell.
Does coolant go to heater core?
As coolant circulates through the engine, some of that hot coolant passes through the heater core in the dashboard. As you use the temperature controls on your dashboard, your blower fan then moves the warm air to where you need it, for defrosting your windshield or heating the interior.
How many actuators does a car have?
Typically, vehicles have 3 or 4 actuators. Vehicles with rear controlled HVAC will often have additional actuators to control the auxiliary unit, bringing the total per vehicle to as many as 6.
