Table of Contents
Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.
What is the best placement for cabinet pulls?
For pulls, you want the bottom of your pull to fall in line with the cabinet rail. Be sure to adjust your installation holes if needed. You do not want your pulls extending into the rail. For slab doors, you will want the hole placement to be equidistant from the bottom and side of the cabinet.
Do you put knobs or pulls on kitchen cabinets?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Where do you mount drawer pulls?
Most drawer pulls are centered on the drawer fronts, but if the cabinet you’re working on has two or three drawers the same size and one larger one at the bottom, install the bottom knob (or pull) higher than the center of that drawer front. Install it so all the knobs on the cabinet are spaced evenly.
Should kitchen handles be vertical or horizontal?
The universal rule is that handles are placed vertically on doors and horizontally on pull-out drawers. Stand in your new kitchen and hold your handles against the drawers and cabinet doors to try out different heights and positions for each of them.
How do you measure for drawer pulls?
Place the drawer pull on a work surface with the threaded posts facing up. Measure from the center of the screw hole in one threaded post over to the center of the other screw hole with a tape measure. This is the measurement required when selecting replacement pulls.
How do you decide between knobs and pulls?
Knobs have smaller profiles than handles, are less expensive, and can be used for both drawers and cabinets. They are slightly easier to install than pulls since you only need one screw to secure the knob to the surface. Pulls are larger than knobs, make more of a statement, and tend to be easier to grip.
How many pulls should a drawer have?
Drawers wider than 18″ need two knobs/pulls, whereas drawer narrower need only one. If a drawer is wide enough to need two knobs, they should be set about 1/6th of the drawer length from each end (roughly). Single pulls or knobs on drawers should be laterally centered and slightly higher than vertical center.
Do you put pulls on fake drawers?
I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.
Where should door handles be placed?
All door handles, pulls, latches, and locks should be installed at least 34 inches from the finished floor. On most people, this means that the door handle will be comfortably situated around their hip area. On the flip side of things, your new door handle should not be higher than 48 inches above the finished floor.
How do I choose a kitchen handle?
When choosing handles it is important to make sure they are good quality and are well designed. Think about how many times you open and close the cabinet doors and drawers in your kitchen. You will want your handles to be as comfortable as they are stylish. Test out the handles you intend to buy.
What size pulls for 36 inch Drawers?
Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall. Cabinet doors 24-36 inches tall are best adorned with pulls 7-12 inches long, while cabinets taller than 36 inches such as pantries, built-in appliances and pullouts should be accompanied by pulls longer than 12 inches.
How do you measure for new dresser pulls?
The Center-to-Center of any drawer pull is the distance between the center of one screw hole to the center of the other. Measuring the center-to-center of the drawer pull is key in determining what new hardware will fit and whether you’ll need to drill new mounting holes or fit into existing ones.
Can you mix knobs and pulls in a kitchen?
Yes. You can mix knobs and pulls. It’s recommended to use pulls for cabinets that are higher up and knobs for lower style cabinets. Lower drawers that slide are typically fitted with a pull handle.
What kitchen hardware is most popular?
Bar pulls remain the most popular kitchen cabinet hardware. They look classic, come in a variety of finishes and are usually quite affordable when purchased in bulk.
What hardware looks good on white cabinets?
Hardware on white cabinets will stand out and steal the show, so it’s a great opportunity to go bold! If you have warm tones, go with gold, black, or bronze hardware. If you have a cold grey tone, then silver, pewter, black, and stainless steel hardware will work.
What is standard for cabinet pulls?
For standard size cabinetry (dimensions of 12″ – 36″) the most common pull sizes are 3”, 4”, 96mm, and 128mm center to center (from one screw hole to another). Standard knob sizes are 1 1/4″ or 1 3/8″.
What is the rule of thumb for cabinet hardware?
A good rule of thumb for traditional or transitional style pulls is that they should be about one-third of the length of the cabinet drawer. Drawers larger than eighteen inches wide may require more than one pull or knob. Pulls are installed with two screws through two points of contact on a door or drawer.
