Table of Contents
Cabinet knobs are placed opposite of door hinges. On wall cabinets, knobs are usually placed 2-1/2” to 3” from the bottom corner of the door. On base cabinets, they are placed 2-1/2” to 3” from the upper corner of the door. If your drawer is 24” or wider, you may choose to place a second knob.
Do cabinet handles go in the middle?
For standard drawers, the correct cabinet knob placement is typically with knobs centered vertically, so they will be in the center of the panel. For extra deep drawers, you may install knobs centered in the top third of the drawer or on the top rail if you prefer.
Where do pulls go on drawers?
When it comes to cabinet pulls placement for drawers under 24”, pulls are most often centered and installed in the middle of the drawer panel. This creates a really clean + high touch finishing look for your cabinetry. Like with knobs, if the drawer is 24” or wider you can add a second pull.
Where do you put cup pulls on drawers?
Cup Pulls: Cup pulls are only ever used on drawers, and I like to center them in the middle of the drawer slab. If you have a 5 piece drawer (top and bottom rails, inside panel, and side rails) you want to make sure the hardware itself will fit (centered) in the middle panel before purchasing and installing.
Should kitchen cabinets have knobs or pulls?
There are no strict rules to follow when choosing whether to select a knob or a pull or both. One preference is to use knobs for all doors and pulls for all drawers. For any large door such as a pantry and any pull-out door (including pull-out base pantries or trash pull-outs), use a pull.
Should kitchen handles be vertical or horizontal?
The universal rule is that handles are placed vertically on doors and horizontally on pull-out drawers. Stand in your new kitchen and hold your handles against the drawers and cabinet doors to try out different heights and positions for each of them.
Where should door handles be placed?
All door handles, pulls, latches, and locks should be installed at least 34 inches from the finished floor. On most people, this means that the door handle will be comfortably situated around their hip area. On the flip side of things, your new door handle should not be higher than 48 inches above the finished floor.
Should cabinet pulls be centered?
As far as the height of your drawer hardware, the classic choice is to center them vertically. With multiple drawers stacked on top of each other, choosing this placement makes each knob a little lower and harder to reach.
Where do cup pulls go on Shaker cabinets?
Center of the Stile: Knobs and pulls can be placed halfway up the stile of your Shaker door. Keep in mind you’ll want to be able to reach the handles, since they will be placed higher up along the stile. Just Above or Below the Corners: Place the knobs or pulls 2” to 3” from the lower or upper corner.
Should drawer pulls be centered?
Pulls should be placed horizontally on drawers. For small drawers (less than 24” wide) center the knobs or pulls in both directions. Just like on larger drawers, pulls should be placed horizontally. Knobs and pulls can also be placed centered at the very top of the drawer panel, where the drawer rail begins.
How Big Should Cup pull be?
There is no right or wrong size to choose, but we do recommend choosing pulls that have at least a 3-3/4″ center to center (the distance between the screw holes). This size looks pleasing on most cabinets, while still being large enough to grip comfortably. 5″ pulls are also an excellent choice.
Do cabinets look better with hardware?
Cabinet hardware should match existing metalwork such as your sink faucet, or appliances. This creates a unified look in any kitchen or bathroom. There is a time and place to mix and match finishes… but not with hardware.
Should my kitchen cabinet pulls match my faucet?
Most of the time the kitchen faucet should match cabinet hardware!” But, sometimes strategically placing different metals next to each other can work for you, add interest or even make a statement.
How do you decide on pulls or knobs?
Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter. Large Drawers that are 30” to 48″will require a pull that is longer than 8″ or a knob that is 1″ in diameter or greater. Using two pulls or knobs for a large drawer also works great.
Do you put handles on fake drawers?
I would recommend putting pulls on the dummy drawers it allows for consistency. Good design is always consistent. It will also give the illusion that these drawers are not fake. The idea of putting a minimal intrusive towel bar works well because then it will serve more for function then aesthetics.
How long should bar pulls?
Bar Pulls are traditionally measured center-to-center and they should not exceed 1/3 of the length of a cabinet door or width of a drawer. Pulls 3-7 inches in length will sit the most comfortably on doors less than 24 inches tall.
How long should cabinet pulls be?
Determine Size While there is no set rule, we generally recommend that the pull length is approximately 1/3 of the cabinet or drawer width. Small Drawers that are 12” or less typically work best with a pull that is 3” to 4” long or a knob that is 1” in diameter.
