Table of Contents
When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.
When traveling with a forklift load the load should be lifted?
Lift the load and tilt it back a little more before traveling. Keep the forks 6 to 10 inches above the ground to avoid potential hazards on the ground. Remember that forklifts are top-heavy. Carry the load low and tilted back.
When transporting a load it should be kept?
Explanation Loads should be kept over, or in front of, the rear axle. Only experienced riders should carry loads on their motorcycle.
When traveling with a load on a level surface you should raise the forks approximately how high from the floor?
When traveling on a level surface, you should raise the forks about 12 inches with or without a load. Dock plates should be visually checked by the lift truck operator.
When traveling with a load the load should be lifted the minimum amount necessary to clear the floor?
Lower the load so that its lowest point is 15 to 20 cm (6 to 8 inches) from the floor. While traveling, keep the load at a safe travel height. See Traveling & Maneuvering.
When traveling with a load on an incline always travel with the load?
When traveling with a load, the load should point up the incline, regardless of direction of travel. Going up the incline: Drive forward. Forks pointed upgrade.
When should you mount and dismount a lift truck?
When mounting or dismounting a forklift, always: Face the vehicle. Never jump off. Use a three-point stance (always have both hands and one foot or vice-versa in contact with the unit) Wear certified safety shoes (oil resistant and non-slippery) Wear suitable clothing (do not wear loose clothing or dangling jewelry).
How do you transport a loader?
Travel up the ramp with the heaviest end up when you are loading the equipment onto the trailer. When loading or unloading the machine, run the engine at the lowest speed setting and travel at the slowest speed possible. Additionally, keep in mind the machine should be properly distributed on the transport vehicle.
How do you transport a wheel loader?
If you are transporting larger wheel loaders, you will need RGN trailers for safe transportation. For the smaller wheel loader, step deck trailers or hotshot trailers are the best vehicles for transportation while compact wheel loaders can be shipped quickly and safely with flatbed trailers.
When transporting a load you should not raise your load more than 8?
When transporting a load, you should not raise your load more than 8″ off the ground. You can drive a lift truck over any type of surface.
How should a loaded lift truck be driven on a ramp?
Loaded forklifts must be driven with the load pointed up the ramp (good standard practice is to ALWAYS drive with the load pointed up the ramp or slope). Raise levels should be limited to the minimum height necessary for ground clearance.
When travelling on slopes with a reach truck How should the load be carried on the forks?
To reduce risk: Always travel load uphill, forks downhill — if travelling with a load, it should always face uphill; if unladen, forks should face downhill. This will improve stability, traction and adhesion, and applies regardless of the direction the operator is travelling in.
When traveling with empty lift forks The forks should be in what position?
It is a good practice to put the fork arms just below the front axle of the forklift and it should be as close to the ground as possible. When the forks are too low, it could scrape the floor surface.
When should a lift truck inspection be performed?
OSHA requires that forklift vehicles have to be inspected at least daily, or after each shift when used around the clock. You will find this requirement in the Powered Industrial Truck standard at 1910.178(q)(7).
What should you check before lifting a load?
Check out these safe lifting and handling tips, recommended by the Health and Safety Executive. Think before you lift. Keep the load close to the waist. Adopt a stable position. Ensure a good hold on the load. Do not bend your back when lifting. Do not bend the back any further while lifting. Do not twist when you lift.
When carrying a load that obstructs the driving view the operator should drive in reverse with the load behind them?
28. The driver will slow down and sound the horn at cross aisles and other locations where vision is obstructed. If the load being carried obstructs forward view, the driver will be required to travel in reverse, with the load trailing.
When traveling down a ramp or incline you should?
When going down a ramp, drive in reverse with the load and keep the forks pointed up the slope. When traveling without a load, the forks should always point down the slope. The forklift operator should also drive in reverse up the ramp or drive forward when going down the ramp.
When carrying a load and driving a lift truck down a ramp or incline you should carry the load on the upside?
When your operators are traveling with a load, the load should point up the incline. This would include going up or down the ramp.
When travelling with a load on your forks you should?
Travel with forks as low as possible from the floor and tilted back (usually within 10-15 cm (4 to 6 inches) above the floor). Match speed to, load, presence of pedestrians, obstructions, and driving and workplace conditions, including slippery surfaces.
What is the 3 point entry into a lift truck?
Use the correct procedure when mounting or dismounting a vehicle or forklift, you must have three points of contact – either two feet and one hand, or two hands and one foot and must be facing the lift truck. Avoid Dismounting the vehicle when in motion. Only dismount when it has come to a complete stop.
What is the first thing you should do at the beginning of your shift before operating your pit?
PITs must be inspected at the beginning of each shift to ensure they are safe to operate . These inspections may be performed by authorized PIT operators as long as they are trained on how to properly inspect the PIT .
