Table of Contents
How often should you replace chainsaw bar?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
How long will a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
When should I replace chainsaw chain?
Once the wear markers have been met it’s essential to replace the chainsaw chain. Filing past the wear marker will greatly reduce the chain’s cutting performance, and increases the risk of the tooth breaking off. Ideally you should reach the tooth and depth gauge markers at roughly about the same time.
What causes chainsaw bar wear?
Accidents or improper operating techniques may bend the bar, pinch the rails, or push the drive links sideways against the bar rails, causing irregular wear. Inspect the bar regularly to insure that it is flat, the rails are straight, and that there is no unusual wear.
Can you flip a chainsaw bar?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear. This reduces a chainsaw’s ability to cut accurately.
Why does my chainsaw chain get dull so fast?
With a single contact with the ground while running, a chainsaw can become very dull. This is because the ground contains sand and dust which is abrasive and contains a lot of tiny rocks. To avoid such occurrences, avoid cutting wood placed on the ground.
How many times can you sharpen a chainsaw?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
Is my chainsaw chain dull?
Smoke crops up even though the chain lubrication is in working order and the chain tension is correct. The chainsaw runs in one direction causing a crooked cut. This is an indication of dull cutting teeth on one side of the chain or uneven cutting teeth lengths. The chainsaw “rattles” and “bounces” during the cut.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How long does a new chainsaw chain last?
The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Are chainsaw bars standard?
Not every bar or chain is right for every saw. For example, larger chainsaw bars work best with more powerful saws because it takes more energy to drive a chain around a long bar. That’s why electric saws use bars 18″ and shorter. Similarly, chainsaw chains are measured to fit certain bars.
How tight should a chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
What chainsaw do loggers use?
The Stihl 500i is generally seen as the ultimate logging chainsaw. It is Stihl’s top-of-the-line professional chainsaw and has been designed and built especially for the logging industry and professional arborists.
What chainsaw chains do professional loggers use?
Full-chisel teeth chains are usually used by professionals on large saws. Semi-chisel teeth are rounded, so the risk of kickback is less, and they stay sharper longer. Semi-chisel teeth cut slower but are a better choice in dirty wood than full chisel.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
Can I drill a hole in my chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Should you grease chainsaw bar?
Proper oiling is critical to the performance and longevity of your chainsaw. Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction.
Can you use wd40 on chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
