Table of Contents
Many houses built between 1965 and 1972 were wired with aluminum instead of copper. The wiring itself isn’t a problem; aluminum conducts electricity safely.
When did houses stop using aluminum wiring?
In 1972, the formula for aluminum wiring changed, making it a much safer product. Aluminum wiring was used in single family homes for a few years after that, but was completely phased out by the mid-’70s.
How do I know if my house has aluminum wiring?
Look for #12-gauge wires in the attic or other places where wiring is readily available. If you see only #12 and no #14, aluminum wiring may be present. Aluminum wire must be one wire gauge size larger for a given circuit than if copper was used.
What type of wiring was used in 1960?
In North American residential construction, aluminum wire was used for wiring entire houses for a short time from the 1960s to the mid-1970s during a period of high copper prices. Electrical devices (outlets, switches, lighting, fans, etc.).
How many house fires are caused by aluminum wiring?
According to the U.S. Consumer Product Safety Commission, more than 50% of home fires happen in homes with aluminum wiring.
Would you buy a house with aluminum wiring?
Aluminum wiring is definitely a concern, but it should not stop you from buying or selling a home. There are ways to deal with aluminum wiring in the home. If you follow these easy steps you can make your new home a safe one for you and your family.
Is aluminum wiring a deal breaker?
Aluminum wiring. Aluminum wiring, which was popular during the Vietnam War era, isn’t terribly common these days. But if your potential home has it, it could mean big trouble. “Problem is, aluminum expands and contracts in the heat more than copper, which causes the connections to loosen up, and then you get fires.”Sep 26, 2016.
Does aluminum wiring have to be replaced?
Even if after 45 years you have not experienced any indication of trouble with your aluminum wiring, it’s a good idea to have it repaired or replaced. Easily recognizable signs include flickering lights, hot light switch or outlet plates, dead circuits or even the smell of burning plastic.
What kind of wiring was used in 1950?
Knob-and-tube wiring was the wiring method of choice for homes until, and in many areas, through the 1950s. Knob and tube wiring was a two-wire system that was quick and easy to install.
What type of wiring was used in 1968?
Due to the high cost of copper, electricians began using aluminum wiring between 1968 and 1974. This wiring can cause loose connections, overheating, and even house fires. Home inspectors need to know about this wiring and be able to inform homebuyers (or homeowners) of their options.
What kind of wiring was used in 1940?
Knob-and-Tube Wiring. Knob and Tube wiring was an early standardized method of electrical wiring in buildings, in common use in North America from about 1880 to the 1940s.
What is one of the problems when making aluminum connections?
The problem with aluminum wiring is that it expands and contracts at a high rate, which can lead to loose connections. Connections between aluminum and copper can also cause oxidation, resistance, heat, increased expansion you get the picture. All of that can lead to a fire.
What are the dangers of aluminum wiring?
Aluminum will become defective faster than copper due to certain qualities inherent in the metal. Neglected connections in outlets, switches and light fixtures containing aluminum wiring become increasingly dangerous over time. Poor connections cause wiring to overheat, creating a potential fire hazard.
How common is aluminum wiring?
According to the Consumer Product Safety Commission, there are approximately two million homes and mobile homes constructed using aluminum wiring since 1965.
How much does it cost to replace aluminum wiring in a house?
The cost to repair aluminum wiring: $85 to $200 per outlet. The cost to replace aluminum wiring: $300 to $500+ per outlet.
Can you connect copper wire with aluminum wire?
The only way considered safe to connect copper and aluminum is through a splice connector. Specifically, you have to connect the wires individually so they are not prone to corrosion. The effectiveness of “pigtailing” using twist-on connectors has been evaluated by CPSC staff.
How do you fix aluminum wiring in a house?
Completely replace your home with copper wire. Pigtail the aluminum wire ends with special crimp connectors called COPALUM. Connect the aluminum wire ends with aluminum to copper AlumiConn wire lug connector.
Is Pigtailing aluminum wiring safe?
CPSC staff considers pigtailing with a COPALUM con- nector to be a safe and permanent repair of the existing aluminum wiring. The repair should include every connection or splice involving aluminum wire in the home, in- cluding outlets, dimmers, switches, fixtures, appliances, and junction boxes.
Is copper or aluminum wire better?
Aluminum Wire vs Copper Wire For its ease of use and ability to effectively conduct electricity, copper is the best kind of wiring for your home. Copper wiring is more stable than aluminum and smaller conductors are needed to transmit power loads. Overall all it is more durable and performs better than aluminum wiring.
When was aluminum wiring used in Florida?
Aluminum wiring in the new construction of homes was prevalent mostly from 1964/’65 to 1974/’75. Unfortunately this was also a time that Federal Pacific Electric panels were used.
