Table of Contents
Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.
What is the best material for fascia boards?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
Can I use pressure treated wood for fascia?
It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
What size boards are used for fascia?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
What kind of wood is used for soffit and fascia?
Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
Can I use plywood for fascia?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
Can you use 2×6 for fascia?
Around here everyone uses 2×6 fascia and then covers it with aluminum fascia. If you are leaving the fascia as wood to be painted then the finished face board is better to wider. So you could use 2×4 frame work and 5/4 or 1×6 fascia boards.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
How thick should a fascia board be?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.
Can you use plywood for soffit?
plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What material do you use for soffits?
Materials Used for a Soffit Board The first material for soffits is wood. If you want to have an old look for your house, you may choose wooden soffits. Proper maintenance of wooden boards can make it last. The uPVC (unplasticized polyvinyl chloride) is one of the most popular soffits.
Does fascia board have a groove?
Skipping Channel Grooves on Fascia Covers When installing the covers, it is recommended that you fasten each subsequent piece to the fascia board. This is made possible by the channel grooves on the fascia covers where the different parts lock. However, some roofers tend to screw one channel groove and skip the next.
How thick is a soffit board?
While not all soffit board sizes are the same, the width of most soffit falls in the range of 16 inches to 24 inches when used to cover the eaves of the home. In addition, standard soffit sizes feature a ¼-inch thickness, too, which can help with installation.
How wide should a fascia be?
Standard gutter size for residential homes is five or six inches. At the backside of a 5 inch gutter, the fascia board mounting area will be four inches tall. On a six inch gutter, the mounting area is 5 inches.
Do you install fascia before roof sheathing?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. Add an inch and a half for subfascia, strike a line. Add the thickness of the true fascia, 15/16 in., in this case.
What is the best wood to use for soffit?
Although unsanded and touch-sanded grades of plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What do you use for fascia on a deck?
If you choose to add fascia, any kind of pressure-treated or otherwise rot-resistant lumber can be used. However, if you’ve opted for synthetic decking in one of the many colors available, you’ll want to consider using a complementary PVC fascia. PVC fascia typically comes in 1/2-in.
Can you use poplar for fascia?
Eaves. The leading edge of overhanging eaves on the front and sides of any building is also known as fascia. Fascia board used in this manner can be made from pine, poplar or any other affordable softwood and varies in width according to the design of the building.
