Table of Contents
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
Can you use regular motor oil in a chainsaw?
Chain saw bar and chain oil isn’t rated by SAE like traditional automobile motor oil. If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
What oil can I use in my chainsaw?
If you have the choice, use SAE30 motor oil when it’s hot outside and SAE10 motor oil when it’s cold because the variations in oil viscosity are better for certain temperatures. Hydraulic oil is similar to motor oil and you can use it as a chainsaw bar oil substitute when you have nothing else available.
Can I use 10w30 for chainsaw bar oil?
Normally, you would need to use bar and chain oil to lubricate your chainsaw because this type of oil was specifically formulated to be used on chainsaws. As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil.
Can I use 2 stroke oil as bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
What is the difference between chainsaw oil and motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use olive oil for chainsaw?
Other vegetable oils most commonly used in chainsaws: Olive oil – thicker than canola but not good at low temperatures. Sunflower oil – thinner than regular chain oil.
Can I use vegetable oil instead of bar and chain oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Is all chainsaw oil the same?
Chainsaw oil is not always the same, but you’ll typically be looking at a proprietary blend of refined mineral oils. This will also include inhibitors for oxidation and anti-wear corrosion, plus it will have a high tack additive included to help the oil stick to the bar and chain while it’s in operation.
What can I use in place of bar oil?
Chainsaw Bar And Chain Oil Alternatives Motor oil. If you find yourself in a situation where you need to use your chainsaw but you don’t have any of the correct oil, one of the obvious options is motor oil. Vegetable oil. Canola oil. Drained hydraulic fluid.
Can you use old motor oil for chainsaw bar?
Yes you can in a pinch, but motor oil is much thinner than bar oil and you will use it very fast. Chainsaw bar oil is thick and sticky and is designed to be used on bars and chains.
What weight is bar oil for chainsaw?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated. Electric chain saws use the same type of lubrication for the bar and chain as gas-powered chain saws.
Can you use snowmobile oil in a chainsaw?
Chainsaw oil and the high end motorsports oil may be engineered for their specific targets, but most of that overlaps and it’s fine to run it in saws.
What does 10W30 mean?
Answered January 07 2020. The 10W30 designation on engine oil means that the viscosity of the oil is rated at 10W when an engine is cold and 30 when the engine is hot. This is different than an oil labelled 5W30, which has a thinner viscosity when the engine is cold at 5W.
Can you start a chainsaw without bar oil?
Running a chainsaw without bar oil will cause mechanical problems, and some serious safety issues, such as: Kickback. Chain failure.
How often should I oil my electric chainsaw?
How often should I lubricate my chainsaw? Fill your oil reservoir each time you fill your chainsaw’s gas tank. Make sure that your saw chain, guide bar, and sprocket are always receiving oil from the saw during operation.
Can I use 2 stroke snowmobile oil in my chainsaw?
Modman said: You can run it in just about anything, don’t worry. As mentioned the new Stihl saws have a funky new oiler system, that I would be leary about using it in, otherwise you can run it in pretty well any 2 stroke motor.
Can I use snowmobile oil in my outboard?
It is designed to burn at lower temperatures and rpms that are seen in outboards and pollute the water a bit less when burned. You could probably run sled oil just fine but it may cause a bit more gumming up than you’re used to.
