Table of Contents
What is the best material for fascia boards?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
What wood do you use for fascia board?
Many different types of wood are suitable for fascia boards. Spruce, pine and fir are all popular and relatively inexpensive options. However, some roofers prefer to use cedar, cypress or redwood for fascia boards. While they are more expensive, these woods better resist moisture, even when left unsealed.
Should I use treated lumber for fascia board?
Purchase pressure-treated lumber to replace your fascia boards as a way to extend the life of the repair. Pressure-treated lumber is designed for outside applications and resists rot, moisture and insect damage. Cut the new lumber to size and secure it to the rafter ends with galvanized finish nails.
What size board is used for fascia?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
What can I use instead of fascia board?
Vinyl. Vinyl siding is a common alternative to fascia board. This type of rafter facing does not rot or wear as quickly as fascia board under the same weather conditions.
Can I use plywood for fascia?
Even though plywood siding isn’t a good fascia material, it works well for soffits, which are out of the rain and have to be painted and cut to install light fixtures and vents.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
Can I use 2×4 for fascia board?
Install 1×6-80″ fascia boards to the 2×4 trusses. Install the fascia so the bottom edge of the roof sheathing will rest on the beveled edge. Install 22-1/2″ long 2x4s between the trusses to support the fascia boards where they butt.
Can you use plywood for soffit?
plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What kind of wood is used for soffit and fascia?
Standard soffit material is 3/8- or 1/2-inch-thick exterior plywood in pine (or similar softwoods) or cedar. Common, but much less durable, is Masonite or similar fiberboard soffit, as well as much more weather-resistant fiber-cement.
Can you put aluminum over treated lumber?
One such interaction is when aluminum is in contact with pressure treated wood. The pressure treated wood contains copper, along with other metals, that interacts with aluminum and causes the corrosion. By following a few simple steps, the dissimilar materials can be separated and the corrosion process stopped.
How thick should fascia be?
Replacement fascias do vary in thickness by manufacturer, but the rule of thumb is that to qualify structurally as a replacement board they should be somewhere between 16mm and 25mm thick – our most common range is the 18mm Replacement Fascia.
What is the best wood to use for soffit?
Although unsanded and touch-sanded grades of plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What material is used for soffit?
Wood. Wood is one of the oldest materials used for soffits, and like wood siding is still around today. Also like wood siding, wood soffits have a grain and texture that makes them very visually appealing. They may be perforated or have vents placed in them, or they may be completely solid.
What kind of nails do you use for fascia?
You must use exterior grade nails. A finishing nail, which has a smaller head and can be countersunk, will give a clean look but nails with a head will be more secure. You can hammer it farther into the wood and cover with putty, caulk or wood epoxy before you paint.
Can you use poplar for fascia?
Eaves. The leading edge of overhanging eaves on the front and sides of any building is also known as fascia. Fascia board used in this manner can be made from pine, poplar or any other affordable softwood and varies in width according to the design of the building.
What is Hardi Senepa?
HardieFlex® Senepa 9.0mm is a versatile fascia board suitable for all types of houses. It can be used to highlight intricate roof designs and it operates as backing for gutter systems to prevent water and vermin from entering the structure through the eaves line. It is fire-resistant and deemed to be non-combustible.
What materials can be used for the finished soffit and fascia quizlet?
Soffits can be plywood, hardboard, solid lumber, vinyl, or metal.
Can you use cement board for fascia?
Soffits and fascia board We used fiber cement board to close in the soffits and cover the fascia of the house. Any rotted fascia boards should be replaced prior to covering. The fiber cement board, although durable, is not structurally adequate to support the eaves on its own.
What is fiber cement trim?
Allura™ Fiber Cement Trim has a rich woodgrain appearance on one side a smooth finish on the reverse making it ideal for exteriors where a traditional wood trim look is desired. Fiber Cement will not attract pests including termites and woodpeckers.
Is Hardie trim discontinued?
While your preferred siding brand may have discontinued production for some of their products, you should not be afraid as many options are available. For instance, recently, James Hardie has discontinued their trim supply in 2021 for the Pacific Northwest.
Do you install fascia before roof sheathing?
When sheathing a roof, the first step is to snap a line so that the first row goes on straight. But if you snap it at 40 inches, then the sheathing will not project over the subfascia or true fascia. Add an inch and a half for subfascia, strike a line. Add the thickness of the true fascia, 15/16 in., in this case.
What is Subfascia?
The sub-fascia (or rough-fascia) is part of the framing. It supports the roof sheathing at the eaves, and provides backing for the gutters. That said, many older houses, or those with exposed rafter tails, don’t have a rough fascia.
