Table of Contents
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
What is the best material to put under concrete?
What is the Best Base for a Concrete Slab? Most people build a driveway or a patio so in that case, a good choice would be a mix of coarse and fine aggregate which will create a compactable base. Overall, a mix of crushed stone and stone dust is the best base material for any concrete flatwork.
What is the best sub base for concrete slab?
The best sub-base for a concrete slab is gravel. The soil has to be prepped first before the gravel can be laid down; pouring concrete directly onto rock is not considered a best practice. You can use different kinds of gravel for the subbase as long as it is clean and uniform in shape and size.
What do you put down before laying concrete?
To shore up the subsurface, sprinkle a thin layer of cement sand onto the gravel and dampen it with water. Do not leave any standing water and allow the dampened sand to dry for about an hour before pouring the concrete. Ground preparation is key to pouring sidewalk, driveway or any other concrete slab.
What happens if you don’t put gravel under concrete?
Because concrete is a very porous material, it will absorb any moisture that it contacts. This can cause pooling. Without crushed stone, pooling water will settle under it and erode your slab.
Can I use gravel as a sub base?
If your builder uses the gravel he may find it will dissipate too easily into the ground and will spend more time and money to get the levels needed. I would not advise using the gravel. A well constructed base means your drive will never get sink holes.
Do you have to have gravel under concrete?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
Can I use concrete as a sub-base?
Any potential ‘soft-spots’ in the subgrade can allow the concrete to sink from the center or turn up from the edges. Owing to its inflexibility, the concrete slabs can crack. As concrete is highly compressed and heavy, it may crack under its own weight if not provided a suitable sub-base.
Is sand a good sub-base for concrete slab?
BACKFILL. Unless you are pouring on virgin clay, the area will need to be backfilled with either sand, gravel or crushed stone. This will help deliver an even pour and provide strength to your concrete. Make sure that you level the backfill to a uniform depth of at least four inches.
How much sand goes under a slab?
Because concrete slabs “float” on the soil, soft ground or voids underneath may cause unsupported areas to crack under heavy weight like vehicles. Pack about 4 in. of sand or gravel over clay and other poorly draining soils to provide even support.
Do you need rebar for 4 inch slab?
The thickness of rebar should be no more than 1/8 that of the slab, so a 4” slab shouldn’t have steel greater than #4 or 1/2″ bar. It’s best to check with a Structural Engineer if your slab will bridge or cantilever. What is this? For 4” concrete slabs used for driveways and patios, #3 rebar is common.
Can you pour concrete over dirt?
Long story short, yes you can pour concrete over dirt.
Can you use sand as a base for concrete?
Simply put, sand isn’t sturdy enough to work well as a subbase for something like a driveway. It is also difficult to maintain a level sand surface when pouring concrete, and therefore difficult to maintain a uniform thickness of the concrete slab.
Can you lay concrete over gravel?
Laying a concrete driveway over an existing gravel one is possible, but it is not generally recommended. However, if the gravel in your driveway is small enough, it is possible to create a cement driveway over the existing one.
How many bags of cement do I need for 12×12?
of 40lb bag = 1.76 ÷ 0.011 = 160 bags. To determine how many bags of concrete you will need, divide the total cubic yards needed by the yields, at 5 inch thick, for a 12×12 slab you will need 2.22 yards of concrete, so number of 80lb bag of concrete = 2.22 ÷ 0.022 = 100 bags, No.
Can I use 20mm gravel as a sub-base?
0-20mm ballast is perfect for sub-base and concrete foundations. 20mm screened ballast is versatile and can be used on driveways, footpaths, oversite fill as well as sub-bases.
Can I use old slabs as sub-base?
A sub-base of 75mm hardcore will be installed and compacted on the former raised area and each slab will be laid on a full bed of mortar to an approximate depth of 50mm this will ensure the strength and longevity.” Mar 26, 2018.
What can be used for sub-base?
Some of the most used subbase materials include: Recycled concrete. Granular fill. Manufactured aggregate. Crushed rock. Lean concrete. Recycled materials, such as crushed concrete or brick.
How many inches of gravel do you need for a concrete slab?
You will need 3 inches of gravel under a concrete slab that is 4 inches thick. More gravel is better, but 3 inches is the minimum amount of gravel you should have with a 4” slab. Use ¾” washed and screened gravel, then compact it to level.
