Table of Contents
The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch. There are several factors that determine what subfloor thickness is optimal for added benefits like insulation.
What kind of plywood do you use for subfloor?
Standard plywood can be used for subfloors, but a better material is 3/4-inch tongue-and-groove plywood subflooring. The tongue-and-groove edges interlock to resist movement along the panel edges and create an overall stiffer floor.
Can you use 1/2 inch plywood flooring?
Can I use 1/2 inch plywood for flooring? – Quora. Sure, I do it all the time in sheds, or other areas where you don’t expect to walk through a lot. It usually requires the supporting joists be placed at 8 or 12 inches on center (apart).
Is plywood or OSB better for a subfloor?
The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.
Is 18mm plywood OK for flooring?
Plywood is the desired material for use in domestic flooring, but this particular board is extremely multi purpose. These boards can be used in a number of ways, including site hoarding, rood decking and even vehicle body work.
Can I use 7/16 OSB flooring?
Oriented strand board, or OSB, is a wood structural panel that can also be used for flooring. It is made from shredded strands of wood pressed together with wax and a special adhesive, then hot pressed into a panel with up to 50 layers of strands. OSB can be used for subfloors, although it is not as common as CDX.
What size screws 3/4 plywood subfloor?
You’ll want the screw to go about an inch past the plywood into the joist or underlying layer beneath it. So if your subfloor is 3/4 of an inch thick, any screw about 1 3/4 inches long will do the trick. If the plywood subfloor you’re placing is 5/8 of an inch thick, you need a screw about 1 5/8 inches long.
Can sheathing plywood be used for subfloor?
Like Sturd-I-Floor, Rated Sheathing may be plywood or OSB. When used as a subfloor, Rated Sheathing typically requires installation of an additional layer of underlayment on top of it before finish flooring can be applied. The underlayment requirements vary depending on the finish flooring.
Do you need tongue and groove for subfloor?
For subflooring, you use tongue and groove plywood. The tongue and groove are only along the 8 foot edges. On the four foot edges, your seams will fall on joist tops, so no need for tongue and groove.
What is the best material to use for a subfloor?
Plywood is considered the most popular material used for subflooring, it has been used since the 1950s and remains one of the top choices for contractors. Standard plywood works perfectly fine as a subflooring material, but the best option is ¾” tongue-and-groove plywood subflooring.
Do I need 2 layers of subfloor?
That’s the usual approach. Almost no one puts down double-thick subfloor in residential applications (for cost and handling reasons), and both layers need to be fastened to joists. Only thin underlayment can be fastened just to the subfloor.
What are 3 common subfloor materials?
Common Subfloor Materials. There are four primary materials used as subfloor: plywood, oriented strand board (OSB), concrete, and high-performance panels. There are other subfloors materials out there, but they are used in more niche situations. The construction industry is constantly evolving.
How thick do floor joists need to be?
When choosing a joist spacing, check that your floorboards (or sheets) are strong enough to span over the width chosen. As a general rule – floorboards should be a minimum 16mm thick for joist centres up to 500mm and 19mm minimum for centres up to 600mm.
Is 12mm plywood OK for flooring?
The cross-graining technique used in our 12mm ply improves strength, stability and prevents warping, making it excellent for bath panelling, wall lining floors and roofs.
How thick does plywood have to be to walk on?
If you plan to finish the floor in the attic and turn the room into a living space, however, you should always use 3/4-inch plywood. Thinner plywood can flex when you walk on it — even with 16-inch spacing — and this will damage the flooring.
Can I use 12mm plywood for flooring?
I would go with a minimum of 12mm WBP ply as an overlay for ceramic/porcelain screwed at 200cts. I generally take up the chipboard and replace with 22mm flooring grade ply if there is any question about the suitability of the chipboard or overboard with 12mm ply if its OK and height isn’t an issue.
What thickness OSB is used for subfloor?
The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch.
What size OSB is used for subfloor?
For decades, 23/32″-thick OSB has been the most commonly used thickness of OSB subflooring. But a simple switch to 7/8″ panels offers several advantages for accommodating a home’s energy efficiency and for ensuring the performance of finish materials and the overall feel of the floor.
What is stronger 3/8 plywood or 7 16 OSB?
OSB and plywood offer similar (and sufficient) performance in terms of strength and functionality, though plywood is about 7% stronger. Both products will swell when wet, but plywood will return to almost its exact shape when it dries.
