Question: What Thickness Hardibacker For Floors

Table of Contents

We recommend 1/4 in HardieBacker® board for floor applications, unless 1/2 in thickness is needed for transition. On existing structures: Ensure subfloor is not damaged. Replace any loose, warped, uneven or damaged sections of floor.

How thick should cement board be under tile floor?

Floors: A 1/4-inch minimum thickness is needed, but thicker panels are also fine. Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed when spanning the studs and it provides a solid base for the tile.

Do you have to put thinset under Hardibacker?

However, many manufacturers including, both Durock and Hardiebacker not only recommend that you use thinset under their backerboard, but they specify it and will void the warranty on their product if it’s not used. Thinset is going to create a solid surface under tile and prevent flexing that could lead to cracking.

What thickness Hardibacker do I need?

Before you get started, you should determine if your floor is suited to HardieBacker Cement Board. That means you should have a minimum of ⅝” thick exterior grade plywood or 23/32” thick OSB with minimum exposure 1 classification.

Can I use 1/4 cement board on floors?

1/4″ USG Durock® cement board is an ideal substrate for floor and countertop ceramic tile installations. The 1/4″ thickness helps eliminate transition trim when abutting carpet or wood flooring and minimize level variations with other finish materials.

Can I just screw down cement board?

Screw and Joints Do not use drywall screws as they are not recommended to be used to hold the backer board in place. All of your backer board pieces should be cut before they are placed on the floor. It is important to highlight that screws shall not be installed all the way down to the floor joists.

How thick is thinset under Hardibacker?

Can you tile directly over HardieBacker board?

HardieBacker can take up to 200kg of tile hanging weight per m2 so almost any tile can be fixed. Once secured cover the joints with Alkaline-resistant tape and feather the tile adhesive to leave a 150mm wide joint.

What do you put under Hardibacker?

An unmodified thinset (Masterblend) is fine between the Hardi and the subfloor. The reason for the layer of thinset between the cement board and the subfloor is to fill the voids/gaps between the two. It’ll keep the cement board from moving up and down.

Can you use 1/2 inch Hardibacker floors?

Floors. Both 1/4- and1/2-inch cement board are appropriate for floors. To install cement board on floors, cement board manufacturers mandate a 5/8-inch plywood subfloor or OSB underlayment. They also require a 3/4-inch subfloor where tile size exceeds 12 inches.

Can you use 1/4 inch Hardibacker walls?

3 Answers. 1/4″ hardibacker alone is an unsuitable substrate for shower wall tile. If it were attached to properly waterproofed drywall, plywood, or plaster it would be fine. Think about it, one wayward elbow, knee, or hip bump and you may get flexion which would cause the grout (or tile) to crack.

What is the thinnest Hardie board?

Fiber cement board is available in 1/4-inch and 1/2-inch thicknesses. The 1/4-inch-thick board is typically used on floors and countertops.

How thick should a tile floor be?

There is a very specific thickness that is required for floor tile. The average thickness for the floor tile is ½ inch to ¾ inch for each sq of tile. Contrasting with the wall tile which is 3 to 6 inches thick. But too thick floor tile may interrupt the doors from functioning.

Do you have to put thinset between subfloor and cement board?

If you have a concrete subfloor then you should not be contemplating installing cement board over it. Not only is thinset a critical component underneath cement board but the other critical component is the fasteners. And you won’t have the fasteners if you are trying to install it over concrete.

What do you do with a gap between tub and cement board?

Technically, after the tile is installed over the backer board that gap between it and the tub ledge should be filled with an ASTM C920 sealant (caulking e.g. silicone). Although some say you should have weep holes along this gap so any water behind can weep out into the tub.

Do you have to glue down Hardibacker?

Can I use liquid nails or glue with HardieBacker® cement board? No. Where HardieBacker board is being installed over a code-complying subfloor for the attachment of tile, the board is installed over a 3/32”-1/4” thick bed of bonding mortar and then nailed down.

Is backer board required for floor tile?

Whenever you’re laying tile on a wood subfloor, you need to first install cement backer board. Backer board prevents leaks and water damage that could harm your flooring and the structure of your home. You also can’t safely install tile flooring over plywood subfloor or onto an unprotected wood floor.

Is 6mm backer board for floors?

6mm Hardiebacker 250 is backboard used as an ideal substrate for vinyl, natural stone and ceramic tiles, especially designed for floors and countertops.

How thick is backer board for floor tile?

Cement-fiber, or similarly reinforced, backer board comes in standard 1/4 inch and 1/2 inch thicknesses. If you’re installing backer board over an existing subfloor, 1/4 inch is sufficient. If you’re installing backer board in new construction, attaching it directly to floor joists, opt for 1/2 inch sheets.

What size backer board do you use for floor tile?

Half-inch cement backer board is ideal for most tiling jobs, including walls, floors, countertops, and ceilings. For flooring, the backer board should be installed over a 5/8-inch thick OSB or plywood base. For countertops, use 3/4-inch plywood beneath the backer board.