Table of Contents
Ratchets. The vast majority of what you’ll need to turn with a socket will involve a 1/4″, 3/8″, or 1/2″ drive anvil on your ratchet. They all cover a different range of socket sizes.
How do you know what size socket you need?
How to Determine the Right Size Socket for a Nut Turn on the digital caliper and set it to read in inches, not millimeters. Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides. Check the caliper display. Turn on the digital caliper and set it to read in millimeters, not inches.
What is the most common ratchet and socket size in use?
Common ratchet sizes include 1/4-inch drive, 1/2-inch drive and 3/8-inch drive. Having different socket wrench sizes will allow you to operate different socket sizes based on your particular needs. Most ratchets use a geared drive.
What are the 3 common ratchet drive sizes?
Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there’s little room to move the handle.
What is the standard socket wrench size?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters).
What is the most common socket drive size?
⅜-inch drive size sockets are the most common and most available.
What type of sockets are the most commonly used?
Hex sockets are the most common type of socket and come in two main types: hex/6 point sockets and bi-hex/12 point sockets.
What are the most common metric wrench sizes?
What are the most common metric wrench sizes? Most common are the 1/4-inch, 3/8-inch and ½-inch ratchet drivers, but ¾-inch and 1-inch sets are available for heavy-duty work.
Do I need a 1/2 Ratchet?
1/2 ratchets are great for doing suspension and exhaust work but honestly not needed. You can get by with a 1/2 breaker bar and a good assortment of 3/8 sockets.
What is a 3/8 drive ratchet?
A 3/8″ drive can drive sockets of all sizes. It is big enough to apply quite a lot of force, but not too big to fit into tight spaces. 1/2 inch – 1/2″ sockets are generally used for nuts and bolts from around 10mm and up.
What is the drive size of a socket?
Drive size: Both metric and SAE sockets are available in three drive sizes: ¼-inch, 3/8-inch and ½-inch. Each requires a different ratchet and other accessories like extensions. Smaller sockets typically use smaller drive sizes, while larger sockets use the larger drive sizes.
What are wrench sizes?
Wrenches: Standard Combination Wrenches (1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1) Metric Combination Wrenches (6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19) Standard Flare Nut Wrenches (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 7/8) Note: Each wrench may combine two sizes.
What are the SAE wrench sizes?
The most commonly used and sold SAE sizes for wrenches and sockets are: 5/16″ 3/8″ 7/16″ 1/2″ 9/16″ 5/8″ 11/16″ 3/4″.
What size wrenches does a mechanic need?
Most common are the 1/4-inch, 3/8-inch and ½-inch ratchet drivers, but ¾-inch and 1-inch sets are available for heavy-duty work.
What are all the socket sizes?
Metric Socket Sizes Chart 3/8″ Drive 1/4″ Drive 1/2″ Drive 7mm 5mm 10mm 8mm 5.5mm 11mm 9mm 6mm 12mm 10mm 7mm 13mm.
What’s better 6pt or 12pt sockets?
Answer: It’s true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here’s why: (1) Six-point sockets have thicker walls, so they’re less likely to flew.
Which socket drive size should be used on large bolts or lug nuts?
The torque range of the wrench will dictate the drive size. 1/2 inch is pretty standard for larger fasteners like automotive and truck lug nuts.
How do I know what size nut I need for a bolt?
To measure the diameter of screws and bolts, you measure the distance from the outer thread on one side to the outer thread on the other side. This is called the major diameter and will usually be the proper size of the bolt.
Is the diameter of a bolt the same as the wrench size?
When ordering a bolt you will need to determine. bolt diameter, thread pitch, and bolt length. Technician A says that the diameter of a bolt is the same as the wrench size used to remove or install the fastener.
What are the 3 types of sockets?
Three types of sockets are supported: Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries. Datagram sockets allow processes to use UDP to communicate. Raw sockets provide access to ICMP.
What are the types of sockets?
Top 10 Types of Sockets Stream Sockets. These sockets are used on the delivery side of the network environment. Datagram Sockets. The implementation doesn’t give any guaranteed delivery as they work connectionless. Raw Sockets. Packet Sequenced Sockets. Hex Sockets. Socket Bit. Impact Sockets. Spark Plug Sockets.
What are the different type of socket?
There are two types of hex sockets – six point and twelve point. The six-point hex socket has six points (angles) inside the bolt end, making a perfectly even hexagon. The twelve-point socket—also sometimes called a “double hex” or “bi-hex”—has twelve angles in the bolt end.
What is the most commonly used metric fastener?
What Are The Different Types of Threads Found in Fasteners? Metric Thread. Metric thread is the most widely used today, and can otherwise be referred to as ‘ISO Metric’ or ‘M’. UNC. UNC stands for ‘Unified Coarse’ and is the most commonly used thread type in the United States of America. UNF. BA. BSF.
What is the most common wrench?
Open ended wrenches are the most common wrench in home toolboxes and have the same crescent shape as adjustable crescent wrenches but come in fixed sizes. Many open ended wrenches are double sided with a different size of wrench on each end.
